To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *36724 (-10)
  Re: constant green light
 
(...) That the light stays on during Windows Suspend suggests to me that it has something to do with the power management features of your laptop. Try temporarily turning off the power management option and see if the tower behaves differently. I (...) (24 years ago, 22-Feb-03, to lugnet.robotics.rcx)
 
  Re: constant green light
 
Just yesterday I reinstalled my serial IR Tower on a Win 98 machine and had the green light stay on all the time. It turned out to be an issue of 'port confusion'. When I switched ports (put the tower on COM1 and the other device on COM2) the (...) (24 years ago, 22-Feb-03, to lugnet.robotics.rcx)
 
  vision command purchase
 
Hi again! Thanks for all your suggestions, I ended up getting a good deal on the vision command on ebay (only 40 USD (with s/h)). Anyone else looking for it, check out www.ebay.com first, it's got great deals! And once again, thanks! (24 years ago, 21-Feb-03, to lugnet.robotics.vc)
 
  Re: BricxCC on Win XP how
 
I have a nasty feeling this a "facility" in windows at work here. I have noted that the "classic" ports (serial i/o and parallel) "jabber" when windows doesn't think they are in use. My suspicion is that there is some kind of a legacy port plug and (...) (24 years ago, 21-Feb-03, to lugnet.robotics.rcx)
 
  Re: BricxCC on Win XP how
 
(...) If your green light is on all the time I am amazed that you are successful with any communication. Do you need to do the "open the port and wait 5 seconds" procedure to get RIS, javax.comm, and nqc to work? Something BIOS or hardware-related (...) (24 years ago, 21-Feb-03, to lugnet.robotics.rcx)
 
  Re: constant green light
 
(...) By now I have two more clues: 1) Not only does powering down the PC or booting Linux turn the light Off, but so likewise does a Windows Hibernate. 2) Leaving the port open and unused turns the light Off only until I try a Windows Suspend. (...) (24 years ago, 21-Feb-03, to lugnet.robotics.rcx)
 
  Re: BricxCC on Win XP how
 
Again intriguing, again I thank you. /// BricxCC Without Firmware /// (...) Yes, does BricxCC COM1 fail for anyone else when firmware is erased? Anyone? /// Versions /// BricxCC Help About tells me I have "3.3.7.2" of "2/12/2003". Bundled with (...) (24 years ago, 21-Feb-03, to lugnet.robotics.rcx)
 
  Re: BricxCC on Win XP how
 
(...) You are welcome. I'm still a bit muddled as to your current situation re BricxCC and your RIS with or without the firmware installed. (...) If the port is in use NQC always reports, in my case, the following message: Could not open serial port (...) (24 years ago, 20-Feb-03, to lugnet.robotics.rcx)
 
  Re: Proximity detection?
 
Thanks for the reply, André. I've read that the IR emitters are "low-power". Does this mean the red LED on Spybot would have a longer range than the IR emitters if used in proximity detection? Since the LED is recessed, I guess is would have a (...) (24 years ago, 20-Feb-03, to lugnet.robotics.spybotics)
 
  Re: Robotics round table at BrickWest
 
David, Thanks for the response. My primary interest at this time is with alternative LEGO Mindstorm software like brickOS. I was interested what if any was discussed with these. But as you mention I also have a general interest in robots along with (...) (24 years ago, 20-Feb-03, to lugnet.robotics, lugnet.events.brickswest)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR