To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3671 (+10)
  IR Transmit ?!? HELP
 
I recently assembled a Handy Board, everything is perfect except for the IR Transmitter. The IR Tx LED does not light. It is not the LED itself because I replaced it. I can't seem to figre out what's wrong. Please help. Thank You Peter Eacmen (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: IR Transmit ?!? HELP
 
(...) Did you follow the instructions in the HB Assembly debug? at (URL) says: Output Stage If LED9R fails to light after the poke command is issued, trace the following progression of signals. Please refer to the infrared output schematic: * 6811 (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  PWM and encoder
 
Hi, i have some questions about PWM and encoder. I made following tests: 1) Speed : motor(0,100) my encoder count f.e. 20clicks / per second 2) Speed: motor(0,50) my encoder count f.e. 15clicks / per second 3) Speed: motor(0,40) my encoder count (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Digitial input problem
 
Hi all, i have built a handyboard. It works fine. But on Digital PIN 9 "PAI" i got allways high level (1) during test via "hptest.c". I think i haven´t any soldering problems. That´s wrong ??? bernd klein (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
well....I might be the way you are powering the sensors ??? Maybe luck ???? :)))))) Actually I don't why you don't need any of those supporting parts. A short question ...For what range are you using the sensors (are you using the binh signal) ?? We (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  IC stack problem
 
Hello everybody, Is something wrong with this code or is it IC? { int a[4][4], i; for (i=0; i<4; i++) { a[i][i]=i; } } When I type this at the IC prompt it complains: Downloading 79 bytes (addresses C200-C24E): 79 loaded COMPILER ERROR!: 2 extra (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
The reason you don't need a pull up resistor for the Handy Board is because the Handy Board has built in 47k pull up resistors on the digital inputs! -----Original Message----- From: MAR ERICSON <mar@cooper.edu> To: Darkman <lroska@cyberus.ca> Cc: (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: PWM and encoder
 
The nonlinearity has to due with the characteristics of your motor. You will find that a single step of power at the low end has a greater effect on the speed than a single step at the high end, as the motor approaches its top speed. The (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Handy board help
 
You can build a stepper motor controller on a separate circuit board, then remove the motor control IC's off the handy board and use the output signals to control your stepper. Will have to write a program to run it. you will need a min of 4 outputs (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: loading files with IC
 
In fact, that's weird.. I can't answer to that. To me, I'm pretty sure that IC would have gave me an error, like when I try to load a C program without having loaded the ICB containing the special function used by this C program. For example, i (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR