To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3666 (+10)
  Re: Help!! Polaroid problem!!!
 
Are you using a pullup resistor on the ECHO pin? If not that is your problem. The ECHO output is an open collector driver which requires an 4.7 K pull-up resistor between the output and Vcc. The pull-up is necessary for connecting the module to a (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Handy board help
 
I am interested in using the Handy Board, but I have a few questions about it first. Please help. :) I noticed the Handy Board supports 4 motors but I am interested in using stepper motors with it. Is this possible? If so what modifications would be (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  tsl1301 or 1401
 
Has anyone tried to use one of the TI tsl1301 or 1401 linear sensors with the HB. I ended up with a few but am having a tough time trying to figure out what the data sheets are trying to tell me. Not real clear (to me). Bruce A. Moore (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Why does it seem like everyone except me needs a pullup resistor and perhaps a capacitor somewhere to operate the Polaroid? I've never had any problems without any of these components. ??? The first time I connected the sensor, it worked perfectly. (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  To Prof. Fred Martin: Neat!
 
Hi, I saw your robot at the Trinity fire fighting contest last Sunday. It was neat, and very animate. I was curious to know if you had figured out why it did what it did during your first run (?). And, what type of sensor were you using on the rear (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  IR Transmit ?!? HELP
 
I recently assembled a Handy Board, everything is perfect except for the IR Transmitter. The IR Tx LED does not light. It is not the LED itself because I replaced it. I can't seem to figre out what's wrong. Please help. Thank You Peter Eacmen (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: IR Transmit ?!? HELP
 
(...) Did you follow the instructions in the HB Assembly debug? at (URL) says: Output Stage If LED9R fails to light after the poke command is issued, trace the following progression of signals. Please refer to the infrared output schematic: * 6811 (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  PWM and encoder
 
Hi, i have some questions about PWM and encoder. I made following tests: 1) Speed : motor(0,100) my encoder count f.e. 20clicks / per second 2) Speed: motor(0,50) my encoder count f.e. 15clicks / per second 3) Speed: motor(0,40) my encoder count (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Digitial input problem
 
Hi all, i have built a handyboard. It works fine. But on Digital PIN 9 "PAI" i got allways high level (1) during test via "hptest.c". I think i haven´t any soldering problems. That´s wrong ??? bernd klein (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
well....I might be the way you are powering the sensors ??? Maybe luck ???? :)))))) Actually I don't why you don't need any of those supporting parts. A short question ...For what range are you using the sensors (are you using the binh signal) ?? We (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR