 | | Re: Land mine robot
|
|
(...) Since this is a school project - we shouldn't be telling you how to do it, we should be pointing you towards ways to search for a solution yourself. So... This requires a logical approach (and that always looks good in a school report!) Now - (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Land mine robot
|
|
I'm a Senior in high school and one of the requirements to graduate is that we must complete a Senior project. I know nothing about building sensors or electronics at all. All though I could learn very easily. The purpose of the post was to find (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Land mine robot
|
|
(...) I've been using mine in sand, dirt, middle of the street, etc. for years and haven't had any serious problem. Just be sure to clean everything when you're done. Warm water and gentle dish detergent is what I suggest (don't do the motors (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Hi, I'm new
|
|
"Tjandra J" <lego-robotics@crynwr.com> wrote in message news:046601c2bad2$44...Tjandra... (...) with (...) Check out this site. Look in the "Gallery" (URL) walkers are a real challenge. Good luck with your project. -- Bob Fay (URL) (24 years ago, 13-Jan-03, to lugnet.robotics)
|
| |
 | | Re: RCX Motor Controller
|
|
"Carson Au" <carsonau@excite.com> wrote in message news:H8oBI4.7o2@lugnet.com... (...) The RCX uses Pulse Width Modulation to control the motors. -- Bob Fay (URL) (24 years ago, 13-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Hi, I'm new
|
|
Tjandra, you have posted your message inside a thread with a different topic. You may run the risk of your message never being read. Use the "New" icon at the top right to start your own thread, and try typing in the title exactly what you're asking (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
|
| |
 | | Re: New Parts
|
|
I liked the "Technic Connector Toggle Joint Smooth, Part #44 ". As for the escapement wheel, "bah!" :P (24 years ago, 13-Jan-03, to lugnet.technic, lugnet.robotics, lugnet.modelteam)
|
| |
 | | RCX Motor Controller
|
|
Hi to all, How does the RCX control the lego motor's? Using what? Some basic facts forward - forward current backward - backward current Float - contacts opened Stop - contacts shorted carson (24 years ago, 13-Jan-03, to lugnet.robotics)
|
| |
 | | Re: I2C device for the RCX
|
|
"Bastiaan v.Kesteren" <b.van.kesteren53@zonnet.nl> wrote in message news:H8nvnF.2rz@lugnet.com... (...) takes (...) package, (...) A 3% error rates (7 out of 250 messages) is far too high. I would have expected error rates under 1 in 10 million (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
|
| |
 | | Re: I2C device for the RCX
|
|
"Bastiaan v.kesteren" <b.van.kesteren53@zonnet.nl> wrote in message news:H8o02v.Gpz@lugnet.com... (...) 375ms, which is (...) at the sensor (...) 6360Hz. (...) I don't understand your references to clock pulses. The I2C protocol is edge triggered (...) (24 years ago, 13-Jan-03, to lugnet.robotics)
|