 | | Rere: Smooth PWM in IC 3.1?
|
|
At 08:17 PM 4/11/98 -0600, I wrote: <snip> (...) <snip> Correction: You'll also need Julian's lib_hb.c to go with it. Again, rename your current version first so you don't overwrite it. Put the new one in the libs directory where the old one was, (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | 16 digital outputs as Fred suggested
|
|
Hi guys, I needed 16 digital outputs for my handyboard, so I put up a very simple expansion board the way Fred suggested in his handboard FAQ: I connected two more hc374 with their d-inputs to LCD-display's data bus (d0 - d7). Then I connected the (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: Multitasking (fwd)
|
|
I duno... I fergot. Sorry. :( It was a long time ago (milage-wise). I didn't use that method of mutitaking anymore and I didn't save the old code. But, I don't think so, I can't imagine that would be my style. I would set a global variable from (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | >1A adapter?
|
|
Hello folks, I am currently using the HB to control a robot tethered to a PC (via the serial/charger board), as I'm using genetic algorithms to evolve controllers. The robot pulls about an amp (with motors, servo, sonar etc.), and I'm running it off (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Analog Encoders
|
|
Hi, when I compile fencdr0.asm, I get "xxxjunk.c"(68): Warning --- Value Truncated "xxxjunk.c"(70): Warning --- Value Truncated "xxxjunk.c"(68): Warning --- Value Truncated "xxxjunk.c"(70): Warning --- Value Truncated Does everyone else get this (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Vector V2x Compass
|
|
Hello: I have a V2x compass and I was trying to hook it into my handyboard using Tom Brusehaver's .icb, .c and instructions as described in the contributed section. I have also grounded the M/S pin on the compass. The EOC pin is sent to the HB thru (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help - Cannot download!
|
|
try using DL.EXE (part of the Interactive C distribution) after following the serial port options directions given the FAQ (under downloading problems). fred In your message you said: (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: 16 digital outputs as Fred suggested
|
|
1. please read the Appendix B documentation in (URL) explains this in more detail than the FAQ. 2. you must the even-numbered Yx signals for output latches. Since Y6 is taken (by the on-board latch for the motor drivers), you're left with Y0, Y2, (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Vector V2x Compass
|
|
Hi Armeen, I have the same problem as you. I thought my HB was faulty or it doesn't work with the 68hc11E processor I use or something. So what I did was: I wrote a very simple IC-Routine. You have to load this program with "load v2x.c" and call the (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
 | | Servo Routines
|
|
Question. I've been playin with the servo routines available from the HB page. One thing I've noticed. The servo's seem to chatter a lot. Is this normal. A routine that does nothing but loop, read the knob and output a value based on the knob to the (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|