 | | Re: Thunderbots Infrared Sensor Circuit Diagram!
|
|
If you'd like to save using an output port or external power supply to power your the sensor, check out Nitin's GP2D12 interface brick at (URL) also posted his circuit diagram. I bought a few of these last year for a class I was teaching and they (...) (24 years ago, 9-Oct-02, to lugnet.robotics)
|
| |
 | | Re: Magnetic Coupling
|
|
"Rob Doucette" <lego@nospam.doucettenet.com> wrote in message news:H3pu6E.4J@lugnet.com... (...) know (...) Page 284 of Jin Sato's Lego Mindstorms Book I never could figure out where the mounts came from for this device. -- Bob Fay (URL) (24 years ago, 9-Oct-02, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Handyboards for Dummies, etc.
|
|
A case as you describe it would be nice. To me it's largely a cost issue. Custom plastic is expensive to set up -- thousands of dollars for an injection mold. Anyone care to open-source a design? That would be a start :-). Fred (...) (24 years ago, 9-Oct-02, to lugnet.robotics.handyboard)
|
| |
 | | Magnetic Coupling
|
|
Some time ago, there was a post describing a magnetic shaft coupling constructed with 3-blade technic rotors and train magnets. Does anyone know where this information and/or pictures are posted? TIA, -Rob. (24 years ago, 9-Oct-02, to lugnet.technic, lugnet.robotics)
|
| |
 | | Thunderbots Infrared Sensor Circuit Diagram!
|
|
Hi everyone, Click here to see the Thunderbots prototype circuit for a infrared range detector. (URL) Robot.htm Regards Carson Au carsonau@excite.com (24 years ago, 9-Oct-02, to lugnet.robotics)
|
| |
 | | microscout programs
|
|
Just received a free microscout courtesy of LEGO. Does anyone know what the 7 programs do? I have figured out power mode. (24 years ago, 9-Oct-02, to lugnet.robotics)
|
| |
 | | Handyboards for Dummies, etc.
|
|
Can someone please enlighten me as to why the handyboard is only available as a bare motherboard? Although that may be fine for experiments in controlled environments, it doesn't work at all well for less than ideal circumstances such as out of (...) (24 years ago, 9-Oct-02, to lugnet.robotics.handyboard)
|
| |
 | | finally works
|
|
finally works.... the problem was in the Makefile.common file, finally change the line: # LEGOS_ROOT=$(HOME)/legOS/ with: LEGOS_ROOT=/legOS-0.2.6/ thanks a lot for your posts!! :-) (24 years ago, 8-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: legOS library path
|
|
(...) Ok. So for cygwin, the path is /legos-0.2.6 (...) Is that right? I think it must read c:\cygwin\legos-0.2.6\mycode. (...) Ok. (...) That is ok. (...) First the good news: Makefile.common and Makefile.user are correctly included. Otherwise, the (...) (24 years ago, 7-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: legOS library path
|
|
(...) To make it so that your code can live anywhere (i.e., not necessarily beneath the cygwin and/or BrickOS root directory you should make the following changes to your Makefile. 1. replace any relative paths (i.e., ../ or ../../ etc.) with (...) (24 years ago, 8-Oct-02, to lugnet.robotics.rcx.legos)
|