To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *34444 (-10)
  Technic Gear Motors. How rugged?
 
Our club is about to have some displays that use Gear motors to run it. Members of the club have asked how long a Technic Gear motor run for before it 'breaks down' or has issues. They also have asked if stopping the motors every so often would help (...) (24 years ago, 31-Aug-02, to lugnet.robotics)
 
  Re: Help: RCX 1.0 power adapter
 
Your comment intrigued me into checking. I grabbed a couple of transformers and checked them (with a 4 1/2 digit true rms meter). Off load (open circuit) one reads 10.4v a/c, the other 10.9v a/c. That is well within Lego's 9 - 12v a/c spec. JB (...) (24 years ago, 31-Aug-02, to lugnet.robotics)
 
  Re: Help: RCX 1.0 power adapter
 
"John Barnes" <barnes@sensors.com> wrote in message news:H1pMt3.Ao3@lugnet.com... (...) apparent (...) I bet if you put that radio shack supply onto a multimeter you'd notice it went as high as 13 volts... Them multi selectors are not very acurate. (...) (24 years ago, 31-Aug-02, to lugnet.robotics)
 
  Re: RCX 1.0 power adapter
 
"Tony Hafner" <lego@NOSPAM.hafhead.com> wrote in message news:H1opsA.EHz@lugnet.com... (...) info (...) of (...) Use a Train power pack. That's what the port had in mind when they made it. I've run pbricks for weeks with no issues. The only (...) (24 years ago, 31-Aug-02, to lugnet.robotics)
 
  i2c protocol with the rcx (was Brainstorms)
 
Hi, I tested the RCX-to-I2C-board from Elector Electronics. I think it's very good for educating and experimenting where the user learns very much about the protocol and function of the i2c bus. (...) Yes, it's right .... you can use the RCX to (...) (24 years ago, 31-Aug-02, to lugnet.robotics)
 
  Re: programming spybot
 
(...) Have you tried making the file extension of your program be ".rcx2" or ".lsc" yet? That's the only way BricxCC can tell it should use LCC32 rather than NQC to compile the file. Compiling MindScript code using NQC will definitely give you a (...) (24 years ago, 31-Aug-02, to lugnet.robotics.spybotics)
 
  Re: Help: RCX 1.0 power adapter
 
I use Radio Shack 273-1631. I have a number of these and I have been using them for a couple of years. These devices have a voltage selector switch which I set to 9v. In fact, I wedge a short length of wooden tooth-pick in the switch slot to avoid (...) (24 years ago, 31-Aug-02, to lugnet.robotics)
 
  Re: Sensor Sampling
 
every time no ? nanobapt ----- Original Message ----- From: Steve Hassenplug <hassenplug@mail.com> To: <lugnet.robotics.rcx...ugnet.com> Sent: Friday, August 30, 2002 3:14 PM Subject: Sensor Sampling (...) measurement time (so I'm told) and I need (...) (24 years ago, 30-Aug-02, to lugnet.robotics.rcx.legos)
 
  Latest Firmware
 
Hey, does anyone have the latest firmware for NQC!! Please attach it to me or anyone else! Carson Au (24 years ago, 31-Aug-02, to lugnet.robotics.rcx.nqc)
 
  Re: Use RCX motor output to switch devices
 
(...) Remko, Starting on page 144, I start the topic discussion on Electronic Output Switching by describing a detail lab project of an Audible Tone Generator. The core switching circuit consists of using a 7805 Voltage Regulator IC driving a 2 (...) (24 years ago, 31-Aug-02, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR