To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *33724 (-10)
  Re: Aborting from ISR
 
Hi, (...) My questions were a bit ambiguous. I don't want to abort the routine running on the ISR; I want (from the ISR routine) to abort a currently running user routine - eg abort something started from the console. So, for example, if a program (...) (24 years ago, 15-Jul-02, to lugnet.robotics.rcx.pbforth)
 
  Re: Light sensor question
 
(...) With obvious mappings, of course. (...) Put another way, at no point does the red LED on the light sensor light up, and I consistently read the same value from the light sensor, regardless of whether I set the mode to RAW or percent value. In (...) (24 years ago, 15-Jul-02, to lugnet.robotics.rcx.pbforth)
 
  Re: Gutting an optical mouse - Part I
 
Does anyone who knows more than me about these kinds of mice know if what is currently on pricewatch is the right thing; go to www.pricewatch.com, click on mice and then search for "optical". It comes up with a Mitsumi device for $9. Is this the (...) (24 years ago, 15-Jul-02, to lugnet.robotics)
 
  yet another question about lnp
 
thanx to mark falco and albert huang for helping me out with lnp_init. But now i have another problem. if i execute lnp_addressing_write at approximately the same time as i recieve data on the serial port, lnp_addressing_write does not return.. the (...) (24 years ago, 15-Jul-02, to lugnet.robotics.rcx.legos)
 
  Re: whats up with lnp_init?
 
(...) I ran into this when using the LNP library to emulate LNP in the RCX as part of emuLegOS (URL) emuLegOS contains a thread safe wrapper for the LNP library. It should be fairly simple to extract that code into your own library for use in non (...) (24 years ago, 15-Jul-02, to lugnet.robotics.rcx.legos)
 
  Light sensor question
 
I want to expand the Scheme procedure (get-light-value <sym | num>) where <sym> is one of 'PORT1, 'PORT2, 'PORT3 and num is either 0, 1, or 2 to the FORTH code 128 <port> SENSOR_MODE <port> SENSOR_CLEAR <port> SENSOR_READ <port> SENSOR_VALUE So, if (...) (24 years ago, 15-Jul-02, to lugnet.robotics.rcx.pbforth)
 
  Connect the ADNS-2030 optical mouse sensor to the Handy Board
 
(...) (24 years ago, 15-Jul-02, to lugnet.robotics.handyboard)
 
  Re: Question, opinion, help - Claw Hands
 
Ok, here's what I came up with. It's a three finger claw deal, offshoot tech from the Super Mech-Bot. I like it. Dual z24 single Worm Gear drive in the center of the hand acuates the fingers. The Mechanical hinged fingers feature a multiplexed (...) (24 years ago, 15-Jul-02, to lugnet.build.mecha, lugnet.robotics)
 
  Re: whats up with lnp_init?
 
"kenneth johansen" <kennethj@stud.cs.uit.no> wrote in message news:3D31CF01.37F981....uit.no... (...) Kenneth, I'm not sure if I remember correctly, but lnpd as it is right now might not fare so well with reentrant code (i.e. pthreads) because the (...) (24 years ago, 15-Jul-02, to lugnet.robotics.rcx.legos)
 
  Re: RCX to RCX communication
 
"Luke Ma" <Luke_Ma@brown.edu> wrote in message news:Gz83nF.7D9@lugnet.com... (...) and (...) outputs. (...) eep. erm... we never posted RCX-RCX sample code up. never gave any of the students two bricks. and the LNP code up on our website has our own (...) (24 years ago, 15-Jul-02, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR