 | | Re: Rover Programming
|
|
(...) OK, why does it need to communicate with the PC? The primary problem is dead reckoning navigation - which is hard on the 'out of the box' RIS because it's very hard to make a robot that can turn a controlled amount or travel a controlled (...) (23 years ago, 24-Jun-02, to lugnet.robotics)
|
| |
| | *** name poll 2nd phase: make your votes ***
|
|
Now is YOUR turn. I've collected the names and present them at the end of this posting. You can vote for ONE ( 1 ) name. Send an eMail to legOS-namepoll@gmx.de with: - the name you vote for - a phrase, choosen by you for example: I vote for: (...) (23 years ago, 24-Jun-02, to lugnet.robotics.rcx.legos)
|
| |
| | legOS new name: a remark
|
|
some of you may have noticed that I didn't include some names. I contacted the LEGO group and asked them about their feelings for a new name. I got the following answer: The new name should not include any of our trademarks, such as: LEGO, (...) (23 years ago, 24-Jun-02, to lugnet.robotics.rcx.legos)
|
| |
| | serial wiring problems
|
|
Hi, I’d like to connect a PAK VI PS/2 coprocessor to the Handyboard using its serial port. I’ve taken a RJ-11 telephone cable and cut it into two pieces, so that I’ve got on one side the leads of the cable without the RJ-11 plug which I want to (...) (23 years ago, 23-Jun-02, to lugnet.robotics.handyboard)
|
| |
| | Re: How do I switch other devices with my RCX.
|
|
(...) AHAHAAHAHAHAHAHAHAHAHAHAHAAA! (my kind of humor) O, man, a day without laughter is a day not lived! For a more serious approach: see response to the other response. Thanks anyway, Chris! :D (23 years ago, 23-Jun-02, to lugnet.robotics)
|
| |
| | Re: How do I switch other devices with my RCX.
|
|
Thank You, Rob, for your quick response. Judging from the two comments I've received, I should have elaborated a bit. I wanted to use a relay to switch the other circuit, but the it wasn't exactly clear to me what specifications the relay should (...) (23 years ago, 23-Jun-02, to lugnet.robotics)
|
| |
| | Re: How do I switch other devices with my RCX.
|
|
Use the output (A, B, or C) to turn on the relay (you can pick those up at Radio Shack or wherever). The relay could be used to switch on a separate power source to power whatever device at whatever power/voltage you deem necessary. -Rob "Da Byte" (...) (23 years ago, 23-Jun-02, to lugnet.robotics)
|
| |
| | Re: How do I switch other devices with my RCX.
|
|
(...) Simply pick up the other device and set it aside, then place the RCX in the location where the other device was. Tada! You have now switched the other device with your RCX! (23 years ago, 23-Jun-02, to lugnet.robotics)
|
| |
| | How do I switch other devices with my RCX.
|
|
Hi! Problem: I want to switch other devices with my RCX. Does anyone know a feasible solution to this problem? Thank You! Da Byte (23 years ago, 22-Jun-02, to lugnet.robotics)
|
| |
| | Spybotics
|
|
I don´t know if you have already seen this but maybe you can get some more info from it. (URL) (23 years ago, 22-Jun-02, to lugnet.robotics)
|
| |
| | Re: RCX infra-red code
|
|
hi Vincent, you might take a look here (URL) Mientki (...) In lugnet.robotics.rcx, Vincent Grace writes: (...) (23 years ago, 22-Jun-02, to lugnet.robotics.rcx)
|
| |
| | RCX infra-red code
|
|
Hey! Does anyone know what signals to send from a non-mindstorms infra-red transmitter to the RCX? (For instance how to send "message 1" to the RCX.) You can e-mail your answers to <kttgrace@eircom.net>. (23 years ago, 17-Jun-02, to lugnet.robotics.rcx)
|
| |
| | Re: Syngress Web Site For Ferrari's Mindstorms
|
|
(...) I can confirm you that Syngress quickly solved the problem and those pages are now updated. They're also receiving more errata so they can put those on the site as well. If someone wants to report an error on the book, please write to: (...) (23 years ago, 21-Jun-02, to lugnet.robotics)
|
| |
| | control multiple mindstorms robots using 1 IR tower!
|
|
Hi all! I'd like to control multiple mindstorms robots using one IR tower with replacing the default firmware for RCX unit to leJOS! Is it possible? I do consider the problem of how to distinguish the different RCX units inside the robots within the (...) (23 years ago, 20-Jun-02, to lugnet.robotics.rcx)
|
| |
| | Re: Pole-Balancing Robot
|
|
(...) Wow! Is that ever fun to watch! I'm going to try to make one of my own now. Nicely done Iain! Keep up the great work. Dave!! (23 years ago, 20-Jun-02, to lugnet.org.ca.rtltoronto, lugnet.robotics)
|
| |
| | New blank Handy board PCB for sale
|
|
HI I have some surplus Handy board (blank) PCB for sale. If you are interested have look at (URL) (23 years ago, 20-Jun-02, to lugnet.robotics.handyboard)
|
| |
| | Handy board PCB for sale
|
|
HI I have some surplus Handy board (blank) PCB for sale. If you are interested have look at (URL) (23 years ago, 20-Jun-02, to lugnet.robotics)
|
| |
| | Re: Pole-Balancing Robot
|
|
(...) Perhaps if you succeed you can call it a Legway? (23 years ago, 20-Jun-02, to lugnet.org.ca.rtltoronto, lugnet.robotics)
|
| |
| | RE: Robotic Vision (was: Video image analisys)
|
|
I'm really starting to like this idea. ...wish I had the time *and knowledge* to do a HyperRvCAD :) Examples: (ASCII ART ALERT, use FIXED FONT to see): [VP]>-vs->[DTVP]>-vs...[ZF]->[DT] [DTVP]>-ds(x,y)->[DI...y,m)->[ZF] (...) (23 years ago, 20-Jun-02, to lugnet.robotics)
|
| |
| | Re: DJGPP & LegOS
|
|
Dave, This files are also located on the legOS website (URL) am currently trying to find any information about the process to build these using the current set of tools (gcc, legOS, etc) Ed David Chen <dcchen@pacbell.net> wrote in message (...) (23 years ago, 20-Jun-02, to lugnet.robotics.rcx.legos)
|
