To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *32529 (-20)
  Re: New pbForth 2.1.0 (and firmware speed)
 
Thanks Ralph, this is great news. I just got the new USB tower, and considering my revived interest for pbForth your new version arrives really at the right time. What IMHO would really boost the spreading of pbForth, is the availability of some (...) (25 years ago, 10-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
 
  RE: SpyBots @ Amazon
 
At the risk of digressing and sounding horribly stupid, has there been any (pseudo-/semi-)official word yet on the computer type/capabilities of the SpyBots? Andrew Burton phone. (334) 876-9259 email. superboy@wccs.cc.al.us (...) (URL) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  New pbForth 2.1.0 (and firmware speed)
 
For everyone that has been interested in firmware speed over the last few days, I am ready to announce the latest version of pbForth. This version supports the USB tower under Windows!!!! (URL) An empty loop of 20,000 interations takes less than 1 (...) (25 years ago, 10-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
 
  Re: Light Sensor help
 
"Steve Baker" <lego-robotics@crynwr.com> wrote in message news:3CB39250.8CC16B...ail.net... (...) what (...) you (...) storage (...) If you need to use a lookup table where you know the values of the table at compile time, using a case statement (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  Re: RCX Firmware Speed
 
Dick, Nice post, and an iteresting topic. My timings differ a little for v2.0 beta, but they are basically the same. My timings use an interal timer as do yours. My multi-task measurement shows that the 3mS framework does not apply to every (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  Re: RCX Firmware Speed
 
Firstly, thanks very much for that detailed answer. That was exactly the information I was looking for. Somewhere in the thread it was suggested that each task gets one opcode executed every 3ms, actually, as you show, they all get one opcode (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  Re: Light Sensor help
 
(...) 16 MHz AFAIK, and I bet it could go much faster, at the price of a less reproducible timing. leJOS executes some tens of Java bytecodes per millisecond, an empty 10000 iterations loop containing four relatively simple byte codes runs in 1.4 (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  RCX Firmware Speed
 
This is a follow up to many of the recent posts on the speed of Lego's RCX byte code interpreter. It's a long post but the salient items are in the first few paragraphs. The interpreter is very slow because of all the overhead required to execute a (...) (25 years ago, 10-Apr-02, to lugnet.robotics) ! 
 
  Re: Light Sensor help
 
(...) Hrm. Looks like I need to be more thorough with my multi-task timing tests... my results (which seemed to show only one task getting run in any given timeslice) differ from yours. Unfortunately, I didn't keep good notes of all my measurements, (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  SpyBots @ Amazon
 
The upcoming SpyBots are listed for preorder at Amazon. No pictures yet, but the names and a short description are given for each. MSRP looks to be $60 each. Check it out: (URL) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  RoboLab newsgroup page updates
 
The RoboLab newsgroup page (URL) some updating. The first two links on the left pane don't work anymore. The following two links should replace those first two links: Tufts RoboLab site (URL) or (URL) Education (Dacta) RoboLab site (URL) Pitsco site (...) (25 years ago, 10-Apr-02, to lugnet.admin.suggestions, lugnet.robotics.rcx.robolab, lugnet.dacta)
 
  RoboLab updates
 
If you only read the Robolab newsgroup then you may have missed a helpful post that did not appear in the RoboLab newsgroup. If so, then look at: "Robolab 2.5 patches" (URL) (25 years ago, 10-Apr-02, to lugnet.robotics.rcx.robolab)
 
  Re: Light Sensor help
 
(...) Well, I can think of lots of reasons why you might want trig - if you know what direction you are moving in and how far you've travelled, trig will let you figure out where you are relative to where you started. Using an NQC lookup table isn't (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  Re: Light Sensor help
 
Yuck How much time is the brick spending sleeping then? Roland (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  Re: Light Sensor help
 
(...) Yes, it all appears to be synchronous. However, only one bytecode instruction is run in any given 3ms; any active tasks interleave their instructions. If you have two tasks running, they will each be getting an instruction every other 3ms. If (...) (25 years ago, 10-Apr-02, to lugnet.robotics)
 
  Re: Light Sensor help
 
"T. Alexander Popiel" <lego-robotics@crynwr.com> wrote in message news:20020409200644....eep.com... (...) time (...) loop (...) I did some similar tests and found similar results. The results held up well up to about 3 tasks, but by the time we (...) (25 years ago, 9-Apr-02, to lugnet.robotics)
 
  Re: Overcharged NiCd Batteries?
 
Aha, I know nothing about Handyboards, only about NiCads. I don't see why you need a larger power supply to charge slightly larger cells. Your handyboard is probably only drawing about 75 to 100 mAh to charge at 50 mAh, so a bigger power supply (...) (25 years ago, 10-Apr-02, to lugnet.robotics.handyboard)
 
  Re: Overcharged NiCd Batteries?
 
I'm sorry, I didn't explain myself well enough. I meant to say that I used the 500mA 12V power supply (block AC to DC transformer) by connecting it to the handyboard. From the specifications, the handyboard is supposed to be able to charge 800mAh (...) (25 years ago, 9-Apr-02, to lugnet.robotics.handyboard)
 
  Re: Light Sensor help
 
(...) Wow! That is very interesting. I wonder if the whole thing is synchronous and based on the 3mS sensor read cycle? This would mean that every process gets one of its byte codes "done" during this periodic 3mS spring-clean cycle. I guess the (...) (25 years ago, 9-Apr-02, to lugnet.robotics)
 
  BricxCC release 3.3.4.5
 
I've released another version of BricxCC. This release fixes a couple minor bugs. The Code Explorer feature wasn't processing a file when it was first opened (it was waiting until the first change was made). That should work correctly in this (...) (25 years ago, 9-Apr-02, to lugnet.robotics.rcx.nqc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR