To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3021 (+10)
  Handy Board PWM Routines
 
I've recently been implementing a PD controller on the HB for use in a line following robot, and have been having some problems with instability, especially around the zero point. I was beginning to suspect that the 8 levels of PWM in the HB library (...) (29 years ago, 27-Nov-97, to lugnet.robotics.handyboard)
 
  HB sonar new drivers
 
the new code is improved in the sense that 1. there is a clear schematic and wiring diagram; 2. it does not require the removal of a motor driver chip; 3. all driver code is written in Interactive C. fred (29 years ago, 27-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Handy Board PWM Routines
 
(...) <snip> LDAA speeda ; rotate bits in motor speed ASLA ;Rotate the speed bitmask one bit position. BCC SPDoffA ;Did we set the carry flag by shifting a "1" out ; of the MSB of the register? ADDA #1 ;We pushed a "1" out of the register, better ; (...) (29 years ago, 27-Nov-97, to lugnet.robotics.handyboard)
 
  The frequency of a digital input...
 
Hello all, What is the maximal frequency that we can put on an digital input of HB? French Studant... By, and thanl you... (29 years ago, 27-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Replacement for ZTX614 NPN Darlington Transistor
 
(...) I am currently arranging a supply of the ZTX614, when they are available I will post the price to the list, hopefully early next week. I also supply the Handyboard in the UK at £19-50 for the set (main board and charger/if) including first (...) (29 years ago, 27-Nov-97, to lugnet.robotics.handyboard)
 
  LCD Connector?
 
Hello to ALL, I was wondering if the LCD connector could be used to connect a speech board from RC Systems. Could I unplug the LCD module and use the plug ins for the board w/ an additional power source for the board? Thanks, Randy Eaton (...) (29 years ago, 28-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Smoking serial/charger board...!!!
 
I am having a similar problem (see notes below) - R11 is burning on the serial/charger board. My HB had been on the shelf for a month or so, and it may have been left on AND I had made the motor-power hack (I tapped the center of the battery pack to (...) (29 years ago, 28-Nov-97, to lugnet.robotics.handyboard)
 
  IC problem
 
Hi guys, I know that this exact question came up once before in this newsgroup, but its reply has long since gone to the bit bucket in the sky, so forgive me. Anyway, I can get the following message on my handy-board: Interactive C V 2.81 9/28/93 (...) (29 years ago, 29-Nov-97, to lugnet.robotics.handyboard)
 
  Robotics club in the Los Angeles area.
 
Does anybody know of a club in the Greater LA area. The only one I've found so far is over an hours drive away. Any info would be helpful. Thanks Mike (29 years ago, 30-Nov-97, to lugnet.robotics.handyboard)
 
  Re: IC problem
 
(...) Hi Jeremy, My board does that sometimes too. Are you useing the same telephone cable? Make sure all other programs are closed on your computer. Reset the board by turning it off and then back on. Good luck Terry (29 years ago, 30-Nov-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR