To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *29244 (-10)
  Re: Got my RIS 2.0 set
 
Does the RIS 2.0 graphical language support the scout? -a "Tilman Sporkert (webMethods)" <lego-robotics@crynwr.com> wrote in message news:IJEDLKPEKPPCLPN...ods.com... (...) see (...) set. (...) (25 years ago, 28-Jul-01, to lugnet.robotics)
 
  Re: New LEGO sensors?
 
(...) private persons. Maybe I'm going to inform in Belgium and Germany (mailorder). Does anybody have any tips on this? Grtz., Remko (25 years ago, 28-Jul-01, to lugnet.robotics)
 
  RE: New LEGO sensors?
 
In the US, you can purchase these products from (URL) DCP sensors need an adapter for $55 to connect them to the RCX. The different sensors are in the $55 - $195 range. These are not Lego products, BTW. The capacitor is used with the solar cell to (...) (25 years ago, 27-Jul-01, to lugnet.robotics)
 
  IRQ and XIRQ pins on handyboard
 
Hello everybody, Is it a reason why the IRQ pin of the 68HC11 is not available. On the schema, seems that this pin is always up. If I look in the pcode.asm, the interrupt vector for IRQ ($BFF2) is set to RTI (BadInt) So, if I need to link a device (...) (25 years ago, 27-Jul-01, to lugnet.robotics.handyboard)
 
  New LEGO sensors?
 
Have you seen these? (URL) Johan Hjertman (25 years ago, 27-Jul-01, to lugnet.robotics)
 
  LMD18200
 
Hi, I have a question about the PCB that Matt Harlan have made for an LMD18200 H-Bridge. In that PCB seems that the Thermal Flag Output of the chip goes directly out and ready to connet to the HB, but this output will not be, in the case of set, of (...) (25 years ago, 27-Jul-01, to lugnet.robotics.handyboard)
 
  RE: Power inlet to RCX 1.5?
 
(...) There are 12 contact pads in the battery bay. One is the + lead to the RCX, one is the - lead to the RCX, and the other 10 are used to connect the batteries in series. You need to supply power to the two contact pads that connect to the RCX (...) (25 years ago, 27-Jul-01, to lugnet.robotics)
 
  Re: A review of 8539 (Manas)
 
Hi, John You can use SetSerialComm(SERIAL_COMM_4800) for RCX2, check NQC Guide. Zhengrong (...) RCX (...) knows (...) (25 years ago, 27-Jul-01, to lugnet.robotics)
 
  Re: Power inlet to RCX 1.5?
 
(...) That's right, Darren, but I'm not from Britain, so I'll look at the product for ideas. Is it necessary to fill the entire battery bay, or will one AA suffice to provide the power needed? Also, I'm not only pondering the technicalities of (...) (25 years ago, 27-Jul-01, to lugnet.robotics)
 
  Re: A review of 8539 (Manas)
 
In lugnet.robotics, Hao-yang Wang writes: <snip> (...) Well, duh! It's Lego(r) and it's Remote Control. Of course John Barnes sussed it. My question is what took him so *long*?? :-) (25 years ago, 26-Jul-01, to lugnet.robotics, lugnet.technic)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR