To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *29164 (-10)
  Re: Maximum sample rate (turn rate) for rotation sensor
 
When using the standard firmware, sensors are sampled every 3 ms. The rotation sensor uses a quadrature encoder with a 1:4 gearing between the axle and the encoder, so there are 16 "ticks" per revolution of the axle. The decoding routine in the (...) (25 years ago, 21-Jul-01, to lugnet.robotics.rcx)
 
  Re: Maximum sample rate (turn rate) for rotation sensor
 
The hardware can actually do (in my testing) up to ~3000 rpm with good accuracy. The problem is with the standard software, which cannot do more than some low number (which may or may not be 500, I don't recall) because of how it samples the HW. (...) (25 years ago, 20-Jul-01, to lugnet.robotics.rcx)
 
  sample code for the remote patch (pc side)
 
Hi, is anybody using the remote patch ? I d be glad if anybody could post or send me some sample code for the pc-side where remote messages are send to the RCX. Thanx, Olaf Christ (25 years ago, 20-Jul-01, to lugnet.robotics.rcx.legos)
 
  rotation sensor question
 
I installed leJOS, got it up and running, then read on the sourceforge site a support question about the rotation sensor, so I decided to test it out. I wrote a first cut at it and it didn't work, just like the support question suggested: import (...) (25 years ago, 20-Jul-01, to lugnet.robotics.rcx.java)
 
  Maximum sample rate (turn rate) for rotation sensor
 
Does anyone know the correct maximum sampling rate for the Lego rotation sensor? This morning I noticed that Dave Baum gives a value of 1250 RPM in his "Definitive Guide" (page 29), but looking at (URL) see a value of 500 RPM. Which is correct? (...) (25 years ago, 20-Jul-01, to lugnet.robotics.rcx)
 
  Re: Source switch?
 
Here is an LCAD drawing of a two-way power splitter that uses a single switch. (URL) post is at: (...) (25 years ago, 20-Jul-01, to lugnet.robotics)
 
  Re: Source switch?
 
Tilman, Thanks for the input, I was afraid the "reversing" switch was going to be my only option. I have a pair of them, but I was hoping for a more elegant solution. jt (...) (25 years ago, 20-Jul-01, to lugnet.robotics)
 
  Heat Seeking
 
Hi all! Does anyone have experience with any kind of heat sensor (that ones used in burglar alarms). A few years ago I heard something about a MIT robot that had a people following and shoot (water gun) behaviour. Despite they did it with patern (...) (25 years ago, 19-Jul-01, to lugnet.robotics.handyboard)
 
  Re: Mystery Part
 
Hehehehe... I have to laugh, Brian. Other people have told you that it is a "Brick Separator", and it is extremely useful. The reason that I am laughing is that when I was just coming out of my dark ages almost exactly two years ago... I was just as (...) (25 years ago, 19-Jul-01, to lugnet.robotics.rcx)
 
  Re: Yet another John Barnes endorsement
 
I've used John's "Four Channel Remote Control". It has always worked without fail. It works in a couple of modes, one of which is perfect for skid-steer type applications. There has obviously been a lot of thought put into his design. -Tim (...) (25 years ago, 19-Jul-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR