 | | Re: Beginners Quest.
|
|
Well, I almost sure that you have to use the A1, the other chips have a different configuration, like they can have an eeprom. (25 years ago, 13-Jun-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Data-transfering RCX -> PC in LeJOS
|
|
I made a small communication package which might help you. See (URL) Kjærgaard "Roger Glassey" <glassey@ieor.berkeley.edu> wrote in message news:GD5Kxq.G6G@lugnet.com... | I hope you can solve your problem; I would be very interested in finding | (...) (25 years ago, 13-Jun-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: Server-side Java -> RCX?
|
|
I have just put a software package for leJOS communication on my project website. (URL) the page you will find a small sample program consisting of a leJOS program and a JSP servlet. Both parts are using the communication package RCXCOMM. The (...) (25 years ago, 13-Jun-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: Need Masses of Technical Info
|
|
hi Sean, Your site is promissing a lot, keep on working! I've not much information for you. You already found my site, where there are some schematics for keeping the tower alive with only 1 diode extra (invented by John Barnes). Good luck with it ! (...) (25 years ago, 12-Jun-01, to lugnet.robotics)
|
| |
 | | Re: Need Masses of Technical Info
|
|
(...) After you get some data, like 768 bytes or something, send another signal from the PC. The RCX waits for this, and then sends another 768 bytes. This should keep the tower on for the right amount of time. Also, be careful of sending too much (...) (25 years ago, 12-Jun-01, to lugnet.robotics)
|
| |
 | | Beginners Quest.
|
|
Hi all there, Plz can somebody tell me if I can use MC68HC11E1, E0 or F1 chip instead of HC11A1. I've just looked into archives and found nothing about that. Thx for help. (25 years ago, 12-Jun-01, to lugnet.robotics.handyboard)
|
| |
 | | Lego LED Lights for RCX Debugging or Decoration
|
|
Hi. I manufacture several types of Lego brick incorporating LEDs. These are small 'lights' which can be attached to RCX motor outputs. Their colour can be set by the motor direction and their brightness can be set by the motor power. You can see (...) (25 years ago, 12-Jun-01, to lugnet.robotics)
|
| |
 | | Lego LED Lights for Debugging or Decoration
|
|
Hi. I manufacture several types of Lego brick incorporating LEDs. These are small 'lights' which can be attached to RCX motor outputs. Their colour can be set by the motor direction and their brightness can be set by the motor power. You can see (...) (25 years ago, 12-Jun-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Need Masses of Technical Info
|
|
(...) RCX->PC is difficult because of the tower hardware. The tower shuts off a few seconds after it completes transmission to save power. Messages from the RCX that arrive during or after the shut off are truncated or not received. The tower works (...) (25 years ago, 12-Jun-01, to lugnet.robotics)
|
| |
 | | Need Masses of Technical Info
|
|
I am a student at the University of North Carolina at Wilmington. I am doing undergraduate research on Neural Networking and Artificial Intelligence, and the Mindstorms have become my choice of implementation. Even though I have found a vast amount (...) (25 years ago, 12-Jun-01, to lugnet.robotics)
|