 | | Re: 27 IR signals by using the LEGO Remote Control
|
|
This is a good idea. You could use the same principle to send 27 different values to a single RCX. I.e. your one and only RCX could act as its own MUX. Here's an encoding scheme that gives you 1 one-key combination, 3 two-key combinations, and 6 (...) (25 years ago, 23-May-01, to lugnet.robotics)
|
| |
 | | 27 IR signals by using the LEGO Remote Control
|
|
I've found a way to provide 27 IR signals from the LEGO remote control. See my site for an explanation: (URL) essence you need 2 RCX, 1 to act as a MUX. (25 years ago, 23-May-01, to lugnet.robotics)
|
| |
 | | Re: Wishlist leJOS
|
|
(...) You could use the JavaComm package, look on the Java website for it. It should not be that hard to set up the port, write to it, and then get replies back. Look at the other Java projects mentioned on (URL) to see how communication is done. I (...) (25 years ago, 23-May-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: Wishlist leJOS
|
|
I (another newbie) also would like to upload data from the RCX to a Windows PC. It looks like adding the data to a StringBuffer would be a good way to save it, but I have not much of a clue about how to write (1) the Java that runs on the PC to (...) (25 years ago, 23-May-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: SHRIMP building
|
|
(...) Yes, something like this: | is a wheel pointed straight, \ and / are wheel turned left or right = is the body Going straight: | | |==| |==| | | Turning left: \ \ |==| |==| / / Turning right: / / |==| |==| \ \ Disclaimer: I haven't actually (...) (25 years ago, 23-May-01, to lugnet.robotics)
|
| |
 | | Re: SHRIMP building was: Re: High Strength Powered Steerable pivot wheel
|
|
(...) Yes, something like this: | is a wheel pointed straight, \ and / are wheel turned left or right = is the body Going straight: | | |==| |==| | | Turning left: \ \ |==| |==| /==/ Turning right: / / |==| |==| \ \ Disclaimer: I haven't actually (...) (25 years ago, 23-May-01, to lugnet.robotics)
|
| |
 | | Re: Will not keep P-Code.....
|
|
Rmoving every chips except 62256 RAM and 74HC132, and try it again if it works. Besides the memory chip (62256), please also check the 74HC373 (under-neath the 62256 RAM). Patrick Hui (URL) Original Message ----- From: "Kurt Telep" <kt25@drexel.edu> (...) (25 years ago, 22-May-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: RCX motor pulsing
|
|
(...) Yes. When you set the power for an output port actually you select the duty cycle of a square wave. The granularity depends on firwmare. With standard firmware you can select between 7 power levels; legOS has 255 levels. bye Bernardo New (...) (25 years ago, 22-May-01, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: Lego Camera and legOS
|
|
(...) IIRC, the identifier chip is different, so it returns a different ID, otheriwse it is a regular QuickCam. Change the driver so it recognizes the different chip, and it should work (at least this is what it seemed to be on the robotics mailing (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: RcxCC Font problem
|
|
(...) That worked. Thanks a lot. (...) No problem for me. I only use my font in regular style. Marc Klein Marc Klein A Mindstorms fan. (25 years ago, 22-May-01, to lugnet.robotics.rcx.nqc)
|