To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *28239 (-10)
  Re: Mindstorms v2.0
 
Can someone help me and tell me from where to download the spirit.ocx.Please give the entire url. thanx in advance amit ----- Original Message ----- From: James Matthews <generation5@btinternet.com> To: Lego-Robotics <lego-robotics@crynwr.com> Sent: (...) (26 years ago, 20-Apr-01, to lugnet.robotics)
 
  RE: H8/300 Assembler/C interface
 
(...) I've just done some more browsing and found this tidbit: (URL) It seems to indicate that tghe registers are always filled and that a long may be split across r2 and the stack. Comments? Cheers, Ralph (26 years ago, 20-Apr-01, to lugnet.robotics.rcx)
 
  Re: Motor with Gear Reduction ??!??
 
Hi... If someone can please give me the specs for the motors that come with the RIS 1.5, I'll be REALLY grateful Waqas ----- Original Message ----- From: "Waqas Khalid" <u970127@giki.edu.pk> To: "Shaun Sullivan" <shaun_sullivan@irco.com>; (...) (26 years ago, 20-Mar-01, to lugnet.robotics)
 
  Re: error from makelx: address out of bounds
 
I've found it. They must be declared as static: static LightSensor s(LightSensor::S3,false); int main(){ ... } Regards. Michael Wisse (...) (26 years ago, 20-Apr-01, to lugnet.robotics.rcx.legos)
 
  Re: was (RCX+PC=Rubik's Cube Solver) RCX & VC
 
Hi, Rainer - I too disagree with some points you mention: (...) but it's not out of the box and I'm a purist. (...) box, I'm a purist. Also, are you saying that while VC operates slot 5, it can activate (let's say) slot 4 and run the two programs (...) (26 years ago, 20-Apr-01, to lugnet.robotics.vc, lugnet.build.mecha)
 
  Re: Distance sensor for RCX based on Sharp GP2D12
 
Hi again, nice work (and nice idea). Do you think you can reduce the latency of 300 ms ? Rainer P.S.: And you ask me about that magnet stuff ?!? ;-) Regards Hardwarefreak ! ;-) (...) (26 years ago, 20-Apr-01, to lugnet.robotics)
 
  Distance sensor for RCX based on Sharp GP2D12
 
Hi all, You will here: (URL) a new interface between Sharp GP2D12 distance sensor and RCX. Simple and inexpensive circuitry, compact design, only one input port used, no external supply needed! As an application example, there is a wall-follower (...) (26 years ago, 20-Apr-01, to lugnet.announce, lugnet.robotics)  
 
  Re: LEGO Electro-magnet
 
Hi Philippe, (...) Hmm, I guess they are NOT protected. (...) Not sure, (I'm not an electrical-engineer please Andreas Peter, help :) ) But, when the coil has a consumption of 9mA at 9V it's 1k. (81mW) So if I undestand it right, you're in parallel (...) (26 years ago, 20-Apr-01, to lugnet.robotics)
 
  Re: was (RCX+PC=Rubik's Cube Solver) RCX & VC
 
Hi Eric, I disagree in some points. (...) Please notice, that you can build your own vision templates. (URL)The RCX cannot run normal RCX (...) That's not true ! The VC software downloads a little program (myprog.txt) to your RCX. This little (...) (26 years ago, 20-Apr-01, to lugnet.robotics.vc)
 
  Re: LEGO Electro-magnet
 
Hello Rainer, True! But simplicity sometimes takes a long time to be acheived ;) But there may be some use in flyback and series diodes: Andreas says that his magnet consumes 9mA, below what is available through sensor ports in active mode. So a (...) (26 years ago, 20-Apr-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR