 | | Re: Yet another Q: IR messages
|
|
To send a message use the following: SendMessage(<variable> or <number>); The variable must be of integer type between 1 - 255 The number must be between 1 - 255 To read a message from the IR port do <variable> = Message(); This will put whatever (...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Yet another Q: IR messages
|
|
Hi Tobias, this could look something like this for example : int global_message; // place to store and read messages for every task task main() { start Read_Messages; // start Receive_Message Task while(true) { switch (global_message) { case 1 : (...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Shutting off illumination LED on Light Sensor for LIDAR
|
|
(...) Thanks for all the tips, everybody. I set out last night to open up my light sensor and add a jumper to allow me to take the LED out of the circuit. I was unsuccessful in getting the casing open, even after cutting the underside latching tabs (...) (26 years ago, 29-Mar-01, to lugnet.robotics)
|
| |
 | | Re: lego cap, polarity, etc
|
|
(...) <snip> The polarity markings Andy Gombos was referring to are printed on the LEGO-compatible package itself. The LEGO "capacitor" is in fact an electrolytic cap with plenty of support circuitry, and I assure you there is no danger of blowing (...) (26 years ago, 29-Mar-01, to lugnet.robotics)
|
| |
 | | Yet another Q: IR messages
|
|
I can't figure out how to use the IR commands. I've tried, read a bit in the documentation, but still have no clue. I'd like to know how to: a) Send a message (and decide what message it should be) and b) learn how to recieve messages Thanks in (...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Shutting off illumination LED on Light Sensor for LIDAR
|
|
I drilled a hole in a 1x2 brick to give the light sensor a better sense of direction and to block the LED. The goal was to have the light sensor seek an IR beacon. (...) (26 years ago, 29-Mar-01, to lugnet.robotics)
|
| |
 | | Re: lego cap, polarity, etc
|
|
No. DO NOT UNDER ANY CONDITION CONNECT AN ELECTROLYTIC (ie one with +/- on the terminals) IN REVERSE. The electrolyte is a high resistant in one direction only. The other direction is nearly a short. You may end up hurt as the capacitor blows up in (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
|
| |
 | | Re: lego cap, polarity, etc
|
|
(...) A couple of comments on this... An 'inverter' with respect to DC creates AC, it doesn't swap polarity. If you're going to use the term correctly always use 'invert polarity' and never 'invert' by itself. If you go into a store and ask for a (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
|
| |
 | | Re: Neural network for legOS... ??
|
|
(...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx.legos)
|
| |
 | | May I use RCX to play a .wav file?
|
|
I want to know if I can use RCX to play a .wav file, does anyone help me? Br Zhengrong (26 years ago, 29-Mar-01, to lugnet.robotics.rcx)
|