 | | Re: light sensor multiplexer
|
|
In lugnet.robotics.rcx, Rainer Balzerowski writes: hi Rainer (...) This is not true since you need to maximum of 60ms after that time out occurs in microconterolor and it chanes the sensor. yes that is true that it is slow for your application. I (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
|
| |
 | | Re: light sensor multiplexer
|
|
(...) I'll bet you can't even measure the power used in the two CMOS parts. Why don't you publish your design so we can pick on it? Michael Gasperi (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
|
| |
 | | Ooooops!
|
|
Ingore the message where I wrote that the RCX didn´t start. It started without showing the "4th" on the lcd screen. Does anyone know how to do that? I mean that when you press the "ON - OFF" button it beeps and shows the "4th" or something. Just so (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: light sensor multiplexer
|
|
Hi Nitin, (...) Yes, sadly but true. That's why I have to use a battery anyway. (Or an output, but I would save it for other tasks.) (...) I understand. I should have explained what i'm doing with the sharps, sorry. I have a task running, that (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Bug in RCX 2.0 beta (Was: RIS 2.0 software now in beta)
|
|
(...) Hi Sebastian I think you're right in your analysis and TLG may silently have fixed the problem, because if you look at the Vision Command installation, you'll find that some of the SDK DLLs are newer in that release. For fun, I copied the DLLs (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx, lugnet.robotics)
|
| |
 | | Re: light sensor multiplexer
|
|
Hi Rainer, I do not understand quite your point about timing. Regarding to power sharp takes much more than what your RCX can give ( my measuremants show that RCX gives RMS current of )15 mA only this is not going to drive your sharp at all. (...) (26 years ago, 21-Mar-01, to lugnet.robotics.rcx)
|
| |
 | | RE: Need for chat server?
|
|
Well ? :> Have I lost this thread or did you give up on the idea? I would hang around #Robotics, #Cybermaster, #VisionCommand, #NQC, #Mecha and #Market I even would create "my own" channel: #CM-RCX-comms hmmm... ok, just a thought, eheh One problem (...) (26 years ago, 21-Mar-01, to lugnet.robotics)
|
| |
 | | RE: RCX & Cybermaster (VLL comms and MicroScout)
|
|
On Tue, 20 Mar 2001, Marco Correia wrote: Actually, if I recall correctly, the sensor inputs are quite happy to accept voltage inputs up to 9V, in RAW mode anyway. It might not be good if they were in an "active" mode, though (rotation sensor, light (...) (26 years ago, 21-Mar-01, to lugnet.robotics)
|
| |
 | | Battery replacement
|
|
Hi, Two of my handyboard, pretty old ones have worned out batteries (apparently one element is not charging anymore !!!). I lokked in the digikey catalog for replacement , but the reference doesn't exist any longer !!! What type of element from (...) (26 years ago, 21-Mar-01, to lugnet.robotics.handyboard)
|
| |
 | | Multiple GP2D02 sensors ?
|
|
Has anyone successfully connected more than two GP2D02 IR range sensors to the handyboard (with expansion board) ? I would like to impliment 4 sensors and be able to read the range from them all.. Thanks ... .. Rob .. (26 years ago, 21-Mar-01, to lugnet.robotics.handyboard)
|