To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *26754 (-10)
  Re: legOS
 
(...) "could not open serial port" generally means one of these things: 1) You told NQC to use a serial port that doesn't exist. By default, it will try to use Mac - modem port Win - COM1 Unix - /dev/ttyS0 You can override this with a -S option. 2) (...) (26 years ago, 12-Feb-01, to lugnet.robotics.scout)
 
  Check out this site!
 
Terry Gathright came across this great site and thought you might want to check it out. We hope you enjoy it! (URL) Gathright wrote: Hi Guys, Check this location for some hi power motor drivers, I have ordered two of the 35 amp boards and will let (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
 
  Re: downloading pcode
 
Make sure that your phone wire between the HB and interface board has four wires, most generic phone wires only have two wires in them. -Dan (...) and (...) MAX232 (...) I (...) any (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
 
  Re: Underwater Sensors
 
James, maybe a moisture sensor out of a VCR could be modified to meet your needs??? They are made to detect condensation in VCR's. but if all else fails... water is a conductor, so you could theoreticly just put two bare contacts on the outer part (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
 
  Re: Short Circute Problem -- EMERGENCY
 
Raju, I have a handyboard version 1.21, on this board the battery led is working properly when it lights at power on and then goes off. According to the manual it should only remain lit when the power is too low indicating a dead battery. So I (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
 
  Re: downloading pcode
 
Brian, I had the same problem with a board I built. It turned out to be the memory was bad. I would check all the solder connections to the memory socket and make sure that it is seated properly. -DAN (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
 
  Re: Underwater Sensors
 
If you had two wires hanging out, stripped at the ends, you could just check the resistance across them. Water usually has less resistance than air. (not a very cool solution but I think it would work) (...) (26 years ago, 11-Feb-01, to lugnet.robotics.handyboard)
 
  What kind of plastic?
 
Hello, Lego is ABS plastic; MEK (Methyl-Ethyl Ketone) is good for glueing it. You might want to search through the lugnet.robotics archive, as there was an extensive thread on this last year. Hope this helps, Simon (...) (26 years ago, 11-Feb-01, to lugnet.robotics)
 
  Re: Scout Troubles****
 
(...) sound like your missing the .DLL file, try downloading the scouttool program again. ALex (26 years ago, 11-Feb-01, to lugnet.robotics)
 
  Re: Sonar and the expansion board.
 
Nick.. I have exactly the same problem.. I couldn't even get the 'clicking' to start with and the chips on the sonar board got a little warm. I then have fitted the diodes in series with the power to the sonar board (connector pin 9) and added a 1K (...) (26 years ago, 11-Feb-01, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR