 | | IC under NT
|
|
(...) IC 3.1 for Windows 95/NT is written from the ground up as a 32-bit windows application, so the serial works fine under NT, regardless of the speed of your machine. If you want to try it out to see if it fixes your problem, here's a 7-day (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | digital ins
|
|
Hello again, I realized a solution to the amplified input problem that is simple and at least worth mentioning. A diode clamp (0-5V) does the job quite nicely, and is easy to build. I got the idea from Horowitz and Hill, "The Art of Electronics", (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help!!!! Handy Board Problem
|
|
I am going to guess this is a software problem on the PC side. If you can boot your computer in DOS mode, try running IC then. Or find an older box :-(. Freeware DOS IC is known to have serial line comms bugs with some fast machines. NT can't be (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Size Conversions
|
|
I apologize in advance as this question is completely of the list topics but I hope that somebody will have the answer. I am currently building a six legged walker using the Handyboard as the main CPU and using a modified Miniboard using the Servo16 (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Microphone on a Handyboard
|
|
If you need more than a +200 gain, try an LM358 in single supply mode and use +5v. These are fantastic op-amps and widely available (Digikey). jm (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: digital ins
|
|
If you want to exaggerate the response, perhaps a LM339 +5v single supply comparator will do. Set up your circuit to go high(+5v) above your 2-3v range of operation. This solves all your input problems. Loads of manufactures make this thing. Data (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Microphone on a Handyboard
|
|
(...) Assuming you've hooked the LM386's ground to ground and the + voltage to 5v, you should be set hooking the output of the LM386 to the analog input. Do not insert a capacitor in series, as might be shown for hooking up the LM386 to a speaker. (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | microphone as a sound sensor?
|
|
Hi all, has anyone interfaced a microphone to an analog input of the HB? I've amplified the signal with an op-amp (LM386) but can't figure how to integrate the (AC) signal into a usable voltage range for the HB. I don't think that just rectifying (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Manipulate the LCD in assembler
|
|
I have write a code for manipulate the LCD in the handy board. Because i can't use a battery backed RAM, i need to write in assembler. Well , i'm really read all the FAQ for LCD and for Handy board (including the apendix B for the 6270) .I'm using (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Help!!!! Handy Board Problem
|
|
Hi! I'm currently assembling the handy board, and i got to the stage where i have the bare minimum to run IC. The problem starts when I try to send commands from IC (ver 2.851) to the handy board (running v 2.81). About 85% of the time i get the (...) (29 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|