 | | stepper motors
|
|
Hi, Thanks for all the responses regarding CdS photo cells. Now I am considering using stepper motors in my project as well. I have seen some postings on this list before regarding these motors. Can anyone point me in the right direction for (...) (29 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Servo as drive motor
|
|
(...) Because the servos are closed systems they don't have a hard requirement that their motors run at the same speed, however it would affect the slew rate which is spec'd so they have to be reasonably close. If you zapped the capacitor and turned (...) (29 years ago, 8-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Magnetic card readers
|
|
Thanks for don't replly to none of my e-mail!!! All it's cool , but i can accept nobody know wath i answer??? Well i really want somebody tell me: "well i don't want to reply you" . I can do work the reader with code in c , and i want to know how i (...) (29 years ago, 9-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Hey Chuck, Being the lazy person that I am I modified another servo instead of figuring out the problem w/ the other one(I'll check it out later...) THE PROBLEM IS SOLVED!!!!!!! They both run much closer in speed. Now I'm off to get the rest of the (...) (29 years ago, 9-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Voltage
|
|
Hello all, Fred Martin may have said something to this list about 12v being ok as a battery voltage.If so does the motor drive voltage go up accordingly? Thank you for your help, Joe Martin Email:joema@mpx.com.au (29 years ago, 9-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: 3v motors
|
|
Yeah, you're right. I hadn't realize that constraint of the L293's. Sorry :b ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the (...) (29 years ago, 9-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Voltage
|
|
Yeah, the 12V goes into the motor power pin of the L293's. Thus you will get a higher than 9.6 motor voltage. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical (...) (29 years ago, 9-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | positioning of robot
|
|
Hello, First my apolgies for my bad english (my dutch is mutch better but afcouse thats becoust dutch is my first language). anyway. im working on a robot and use lego to test the best way for moving a robot. i see 3 options.. 2 weels, 4 weels (like (...) (29 years ago, 10-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | re: magnetic card readers
|
|
dear german, i think what's going on is that you are asking very open-ended questions that require a lot of work to compose a helpful response. if i remember right, your earlier question was with regard to networking using the spi port of long (...) (29 years ago, 10-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | More juice
|
|
Can you parallel a 9.6v eight pack NiCad cell to the HB Nicad pack? Has anyone done this with success? If so, does it charge properly? jm (...) (29 years ago, 11-Aug-97, to lugnet.robotics.handyboard)
|