To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *25214 (-10)
  Re: For you German speakers
 
Go to (URL) the option to translate a web page from German to English. Copy in the URL and hit the button. Voila! You get the page translated into (rather comical and error-filled) English. Its good enough to understand. I hope that helps! Brad (...) (26 years ago, 7-Dec-00, to lugnet.robotics)
 
  Re: For you German speakers
 
Hi, Jonathan It may be asking too much, but is there an english version? It seens very interesting but my german knowledge is too basic... Maybe that would be a good reason to continue learning. :) cya, Mauro Jonathan Knudsen (...) (26 years ago, 7-Dec-00, to lugnet.robotics)
 
  Re: Using Vision Command as a Smart Sensor
 
(...) Nice page. It's such a shame that LEGO didn't think to just allow a person to use the MSG's when a zone is active... That's one huge oversight... Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 7-Dec-00, to lugnet.robotics, lugnet.robotics.vc)
 
  Re: Using Vision Command as a Smart Sensor
 
Rainer Balzerowski <balze2@gmx.net> wrote in message news:G55w18.1Ip@lugnet.com... (...) It does slow down VC a little to leave the 1.0 seconds in the Spin Left. You really notice it if you put long numbers like 100 seconds in. I've incorporated (...) (26 years ago, 7-Dec-00, to lugnet.robotics, lugnet.robotics.vc)
 
  Re: Sharp GP2D12 and Expansion Board
 
I tried replacing the MUX...that wasn't it. I just noticed that I can read analog(19) through analog(16) but I can't read analog(19) directly...must be an address problem....the question is where. "Robin Chahal" <rchahal@hotmail.com> wrote in (...) (26 years ago, 7-Dec-00, to lugnet.robotics.handyboard)
 
  Re: Using Vision Command as a Smart Sensor
 
This works for me. NQC task main() { while(true) { SetUserDisplay(Message(),0); } } -- Bob Fay rfay@we.mediaone.net The Shop (URL) Gasperi" <gasperi@alynk.com> wrote in message news:G55vn0.D3@lugnet.com... (...) command (...) that (...) the (...) (26 years ago, 6-Dec-00, to lugnet.robotics, lugnet.robotics.vc)
 
  Re: Using Vision Command as a Smart Sensor
 
This works for me. NQC task main() { while(true) { SetUserDisplay(Message(),0); } } -- Bob Fay rfay@we.mediaone.net The Shop (URL) Gasperi" <gasperi@alynk.com> wrote in message news:G55vn0.D3@lugnet.com... (...) command (...) that (...) the (...) (26 years ago, 6-Dec-00, to lugnet.robotics, lugnet.robotics.vc)
 
  Re: Using Vision Command as a Smart Sensor
 
(...) I didn't check this out yet, but i guess it does !!?!! (...) Nice to hear ! Thanks ! Rainer (26 years ago, 6-Dec-00, to lugnet.robotics, lugnet.robotics.vc)
 
  Re: Using Vision Command as a Smart Sensor
 
"Rainer Balzerowski" <balze2@gmx.net> wrote in message news:G55v2z.LqB@lugnet.com... (...) or (...) for one (...) I didn't realize VC tried to compensate for the RCX program. I'll fix that comment. Do you think the Spin Left 1.0s command in the (...) (26 years ago, 6-Dec-00, to lugnet.robotics, lugnet.robotics.vc)
 
  Re: Using Vision Command as a Smart Sensor
 
In lugnet.robotics, Michael Gasperi writes: hoped would be developed with Vision Command. Thanks for the posting. (...) Hi folks, i do it in a task like this : int global_message; task Read_VC_Messages () { int j; int local_message = 0; (...) (26 years ago, 6-Dec-00, to lugnet.robotics, lugnet.robotics.vc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR