To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *24654 (-10)
  AI in RCX
 
I want to program AI into RCX that can avoid objects by the readings of 3 three ultra-sonic sensors. I am supposed to use Neural Network. But I difficult as the programming is limited by the RCX (even RCX 2.0 is used) Would you be kind enough to (...) (26 years ago, 4-Nov-00, to lugnet.robotics)
 
  Re: LinuxPPC and "No response from RCX" problem
 
(...) Perhaps timing is a problem. Try: nqc -t 1000 -raw 10 This forces a longer (1 second) timeout per packet instead of the dynamic retry timing. Is the output any different? Echo is coming back from the tower, which means communication between (...) (26 years ago, 4-Nov-00, to lugnet.robotics.rcx.nqc)
 
  Re: LinuxPPC and "No response from RCX" problem
 
(...) Have you tried using setserial to set the correct baud rate and other options? Also note that when using "su" it sometimes doesn't take over all the settings from the user account that you used to log on. Perhaps the sudo command would work (...) (26 years ago, 4-Nov-00, to lugnet.robotics.rcx.nqc)
 
  Re: LinuxPPC and "No response from RCX" problem
 
(...) Umm.. note the prompt ;)) I'd done an su root before testing to avoid permissions problems. This seems like a problem with nqc on LinuxPPC 3Q99, but I can't understand quite what it is as the tower obviously works - the green light is visible (...) (26 years ago, 3-Nov-00, to lugnet.robotics.rcx.nqc)
 
  ANN: Robot Contest in Phila, PA area
 
Hi All, Penn State Abington will host the third annual Robo-TrailBlazers autonomous robot contest on Sat Dec 2, 2000 at 3pm. The contest is open to all students (K-12, college) as participants. The contest is HandyBoard and Lego Mindstorms friendly. (...) (26 years ago, 3-Nov-00, to lugnet.robotics.events)
 
  Re: LinuxPPC and "No response from RCX" problem
 
(...) Did you set the correct permissions for the serial ports (normally they're only accessible by root under Linux) Do a chmod 777 for /dev/ttyS0 (26 years ago, 3-Nov-00, to lugnet.robotics.rcx.nqc)
 
  LinuxPPC and "No response from RCX" problem
 
Hi, I recently bought an RIS kit and from my Windows box it works fine. When I try using LinuxPPC off my PPC Amiga I get the following: [root] /home/chris/nqc/nqc-2.2.r2 >bin/nqc -v -raw 10 Tx: 55 ff 00 10 ef 10 ef Rx: 55 ff 00 10 ef 10 ef Tx: 55 ff (...) (26 years ago, 3-Nov-00, to lugnet.robotics.rcx.nqc)
 
  Re: How2 'count' in NQC
 
In lugnet.robotics, Jerry Kalpin writes: [SNIP] (...) There is an EDGE mode available through the firmware that only counts transitions between pressed and non-pressed (actually some raw threshold value if I remember correctly) states. This sensor (...) (26 years ago, 3-Nov-00, to lugnet.robotics)
 
  Re: How2 'count' in NQC
 
I have noticed this ongoing thread about the difficulties of debouncing and counting switch closures, and I must say that it is a very real problem anywhere electromechanical switches are interfaced to electronics which is orders of magnitude (...) (26 years ago, 3-Nov-00, to lugnet.robotics)
 
  Re: How2 'count' in NQC
 
Steve, this is the third time you have helped me, and this time you obviously spent a lot of time working out the alternatives. First of all, the Wait (DELAY); in my inept code was not to flash every half second. It was to prevent additional counts (...) (26 years ago, 3-Nov-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR