 | | RE: single motor pneumatic pump and switch
|
|
(...) we thought it was all done already! Nice work. Cheers, Ralph Hempel - P.Eng ---...--- The train stops at the train station, The bus stops at the bus station, So why am I sitting at a work station? ---...--- Reply to: rhempel at bmts dot com (...) (26 years ago, 23-Oct-00, to lugnet.robotics)
|
| |
 | | Timing of RCX statements
|
|
I was trying to simulate a serial link by using an output of the RCX. I didn't work and when I analyzed the timing, I found out that the RCX's execution of statements is far too slow for the protocol I wanted to simulate. So I made some measurements (...) (26 years ago, 23-Oct-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | LEGO remote and LNP (legOS 0.2.4)
|
|
Hi I've just got the LEGO remote control (from the Ultimate Accessory Kit), and of cause it dosen't work with legos. So I tried to see, if anyone had done some kind of driver to it, but I couldn't find any, and began hacking in the legOS kernel (...) (26 years ago, 23-Oct-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: VC Camera with Linux
|
|
(...) Please find attached a short mail I sent to Luis Villa for inclusion in the next version of the Linux-Mindstorms-HOWTO. Regards, Hakan --- cut --- Hi, A tidbit of information for the next version of the HOWTO: The Vision Command camera is an (...) (26 years ago, 23-Oct-00, to lugnet.robotics.vc)
|
| |
 | | Re: that _raw_analog undefined thing
|
|
Hi Naomi. The problem is not with the get_char function, I think that is with the analog function. Try to find this files in your IC/LIBS directory: lib_hb.asm lib_hb.c lib_hb.icb Expens.c HBsensor.c The _raw_analog is a rutine and it is defined in (...) (26 years ago, 23-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | single motor pneumatic pump and switch
|
|
Pneumatic pump and switch using a single motor: Do you need pneumatics on your robot? You want to produce the pressure and you want to switch the valve by motors. With my idea you can do both with a single motor. Have a look at: (URL) for my bad (...) (26 years ago, 23-Oct-00, to lugnet.robotics, lugnet.announce)
|
| |
 | | Monitor() and Event()
|
|
Can someone teach me more on Monitor() and Event()? Does the Monitor() check the event status repeatly or we have to make a repeat task to activate the monitoring job? If it is not checking the event status repeatly, why we cannot just read the (...) (26 years ago, 23-Oct-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | MacNQC 2.2a3 compatibility with NQC2.2r2
|
|
I am now using MacNQC 2.2a3. It seems it cannot understand some new syntax than can be used in NQC 2.2r2. (Such as EVENT()...) Can anyone teach me what should I do? Camus Lai (26 years ago, 23-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Rechargable batteries
|
|
(...) If your using the Tower a lot of the time, (Polling etc.) I'd suggest getting a power adapter for 9 volts and use that instead. Saves on power greatly. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 23-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Rechargable batteries
|
|
I had a similar problem with the RCX. I use the RCX and it works well with 1,2V NiCd batteries as soon as the tower uses a regular 9V battery. If I use a rechargable 9V battery I have a problem similar to yours. Try using a regular 9V battery and (...) (26 years ago, 23-Oct-00, to lugnet.robotics)
|