To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *24074 (-10)
  RCX, Servos ,and Pneumatics
 
Hi All, I've just updated my site with new information on controlling standard RC servos with the RCX. Besides the dead-simple schematic that uses Radio-Shack parts, you can even control pneumatic switches! There are a few pictures that show a (...) (26 years ago, 7-Oct-00, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.pbforth)  
 
  Re: NQC versus Lego RCX Code Speed
 
Yes, this explains my observations perfectly! I will probably set up some more experiments--attempting to exactly duplicate the function of my oddly-behaving RCX Code (my currently-running NQC program is very close already), and try to get some real (...) (26 years ago, 7-Oct-00, to lugnet.robotics)
 
  Re: need advice on joining....
 
Use the light gray pegs that have a 1-length dowel on one side and a stud on the other side. These convert holes to studs, so it is easy to make the joint you want. Put one stud next to the cross axle hole in the bend angle beam, skip two holes, and (...) (26 years ago, 7-Oct-00, to lugnet.robotics)
 
  Re: This may be a silly question.... radio control
 
(...) For quick manual control, like say, the Cybermaster is about to do something which you dont want it to, but which its programming and sensors cant deal with in time, say hitting a wall at full speed, and you want to be the hero and go manual (...) (26 years ago, 7-Oct-00, to lugnet.robotics.cybermaster, lugnet.general)
 
  Re: Vision command and Mac
 
Have you tried using Virtual PC (or Real PC)? I believe that Virtual PC at least supports some USB devices, maybe the Camera is supported. BTW, has anyone thought of extending NQC --or any of the other alternative RCX programming environments-- to (...) (26 years ago, 7-Oct-00, to lugnet.robotics)
 
  need advice on joining....
 
Help I am building a gripping mechanism and am using pneumatics to do the squeezing. Due to the orientation of the hole on the base of the cylinder I was "forced" to attach a beam in such a way that is now puts me in a bind. The beam in question (...) (26 years ago, 7-Oct-00, to lugnet.robotics)
 
  Re: Dropping your RCX on the floor...
 
Not if was on when that battery disconnects. I think the memory is powered through a capacitor or somthing like that, when the RCX if off the power to the memory is maintained even when batteries arn't in for a few minuets because of the small (...) (26 years ago, 7-Oct-00, to lugnet.robotics.rcx)
 
  Re: Dropping your RCX on the floor...
 
Yes, it was on, and when I picked it up, it was turned off. I thought "No! It's broken!" but you could turn it on, and the firmware was gone. But doesn't the batteries need to be disconnected for like a minute for the firmware to be erased from (...) (26 years ago, 7-Oct-00, to lugnet.robotics.rcx)
 
  Re: legOS doesn't work under NT?
 
(...) are some (...) problems, (...) Absolutly Yes. (...) 0.2.3 and (...) memcpy.c. I (...) to (...) Begin from these two URLs: (URL) Paolo. --- Indecision is the key to flexibility. (26 years ago, 7-Oct-00, to lugnet.robotics.rcx.legos)
 
  Re: More on Miniboard woes and woohoos.
 
The current version of ICC11 has a builtin downloader that talks to MB. Only for W95/NT/... though. ICC11 works with just about ANY HC11 boards, minus lack of support for paging. (...) -- // richard (URL) (26 years ago, 7-Oct-00, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR