 | | RE: NQC versus Lego RCX Code Speed
|
|
(...) No, the Lego GUI software and NQC both produce code for the same target -- a simple interpreted virtual machine implemented in the firmware. I have never looked at the code produced by the Lego GUI, but I can't imagine it would be that much (...) (26 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Miniboard download random failures
|
|
(...) "expected (...) James, Yes, I am running from a DOS window in W9X. Do I have to boot to DOS mode to correct for this? Uhm, I'm a Mac person, so, have patience, how does one boot to DOS instead of Win95? thanks, DLC (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | RE: NQC versus Lego RCX Code Speed
|
|
Wilcox, Doug (11:04 AM 10.05.2000) wrote: >Hmm. This question seems to have gone the way of my PC-->IR Tower cable >question. > >Let me try to get at the point that most interests me--what is the >difference, at the RCX level, between programs coded (...) (26 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
 | | RE: NQC versus Lego RCX Code Speed
|
|
Hmm. This question seems to have gone the way of my PC-->IR Tower cable question. Let me try to get at the point that most interests me--what is the difference, at the RCX level, between programs coded in NQC and programs coded in RCX Code. Is the (...) (26 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Miniboard download random failures
|
|
(...) Are you running DLM from a dos window in Win9x? I've had this problem but it usually stops when I run it in DOS. Just a thought. -Jim Munro <jimmn@xnet.com> (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | Freeware ICC11 and bad iasm11.exe?
|
|
Me again, I just got the ICC11 freeware from the Miniboard site and installed it, moving the crt.s over as it says to do in the docs, etc. I tried to compile the test compile of icc11 dhry.c printf.c and got a LOT of "phasing" errors, whatever that (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | Miniboard download random failures
|
|
Hello, I just finished building a Miniboard using the HC811E2 processor. After swapping the Rx and Tx lines on my serial cable the download and reset switch do as the manual says. However, when I use dlm to download a program the bootstrap section (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | Cybermaster on sale
|
|
Yesterday I saw that the Cybermaster is on sale at the Bart Smit toy shops in the Netherlands, now only fl. 169,- (approx US$ 70) instead of fl. 449,-. I bought just one... Emile. (26 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
 | | Re: The datalog
|
|
(...) Series of measurements. I've used it to measure light sensor values while doing a 360 degree turn next to a candle (disappointing, the candle made hardly a dent), and to measure raw values for touch sensors while pushing them slowly, 1/100mm (...) (26 years ago, 5-Oct-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Remote dead, what to do?
|
|
(...) Are you sure it is the remote? Maybe your RCX forgot its firmware, then the remote won't work. Jürgen (26 years ago, 5-Oct-00, to lugnet.robotics)
|