 | | Re: IRPD sensors and LegOS (long)
|
|
OK, the IRPD rover just smarter. I had an error in the comments in the previously posted version, references in the initial comments about the Right Side Motor being hooked up to Output B were incorrect, it is actually hooked up to Output C. This (...) (26 years ago, 4-Oct-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Roving Webcam Robot
|
|
Here is a shot through the robot's camera. I just added a Lego gauge. The little gauge is fun, but it times out to sleep. It has a lot of functions... a few more might be fun. (URL) (26 years ago, 4-Oct-00, to lugnet.robotics)
|
| |
 | | Re: A neat idea for touch sensors
|
|
That is a neat idea! (...) (26 years ago, 4-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Dave Baum's scanbot w/ bumper?
|
|
(...) The problem is subtle. Scanbot (at least scanbot2.nqc) assumes that the drive motors are always running. It only alters their direction during steering. In your code you call OnFor(), which turns on the motors, waits a specified amount of (...) (26 years ago, 4-Oct-00, to lugnet.robotics.rcx)
|
| |
 | | Re: The datalog
|
|
(...) Each call to AddToDatalog() uses up one "point". Each point takes up 3 bytes of memory: a 1-byte code for the source of point (sensor, timer, etc), then a 2-byte value. 123456 is too big to fit into the log. This would either generate a (...) (26 years ago, 4-Oct-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Scout poweroff time out?
|
|
(...) thanks. Comments are always welcome....that's not saying that I'll implement everything that anyone suggests, but I certainly appreciate the feedback. NQC wouldn't have gotten this far without the suggestions of the user community. Dave (26 years ago, 4-Oct-00, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
 | | Re: A neat idea for touch sensors
|
|
Wow what a great idea! thank-you! Why didn't I think of that? I almost got my dad to bring me back a cybermaster from europe to get those resistor touch sensors. Now I'll have to try this first. Phil :-) (...) (26 years ago, 4-Oct-00, to lugnet.robotics)
|
| |
 | | A neat idea for touch sensors
|
|
Hi everyone, I was trying to figure out a way to distinguish between two touch sensors on the same port. I have seen a lot of examples on the Web of sensor multiplexers using resistors. Being somewhat of a purist, I wanted to do the same thing with (...) (26 years ago, 4-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Roving Webcam Robot
|
|
Amnon Silverstein (07:05 PM 10.03.2000) wrote: >I have been told that Webcam32 can automatically fix the IP address on >the web page, but I have not looked into this. It works pretty well. What you do is put a copy of your web page locally on the (...) (26 years ago, 4-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Roving Webcam Robot
|
|
Everything is battery powered, so it can run around loose. Unfortunatly, this means it can only stay alive for about an hour, and I can't just leave it online. The laptop is the main bottleneck. I have to turn off all power management or else the (...) (26 years ago, 4-Oct-00, to lugnet.robotics)
|