To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *23849 (-10)
  Capacitor on Sonar Board
 
The instructions on connecting the Polaroid Ultrasonic Ranging System to the Handy Board (at (URL) say to be sure and install the 0.1 uF capacitor in the C7 position on the sonar board. It is unclear what is meant here. Is this refering to the (...) (26 years ago, 26-Sep-00, to lugnet.robotics.handyboard)
 
  Re: NQC & Rotation Sensor
 
(...) Do you have the sensor at a place where one rotation of the sensor = 360 degrees of whatever you're turning? I'd suggest putting it somewhere where it rotates a lot more times than the actual turntable. (You need a touch sensor for 0 this way, (...) (26 years ago, 26-Sep-00, to lugnet.robotics.rcx.nqc)
 
  Re: Communicatin between NQC and legOS
 
(...) OK, but do i have to create this frame using legos ?? I tried but it doesn't work. (thank you so far dave baum ! I received your book today, hope this will help me.) (26 years ago, 26-Sep-00, to lugnet.robotics.rcx)
 
  Re: Advanced programming with Vision Command
 
(...) Is there anyone in the world ? ;-) (...) I managed to use the cam as a sensor (but its still limitated). I did it this way : I wrote a program with the VC - Software with a function for every field. (don't care wich function but it should be (...) (26 years ago, 26-Sep-00, to lugnet.robotics)
 
  Re: Anyone know where I can get RIS 1.0 to 1.5 Upgrade in the UK?
 
I've received a nice email from Lego Shop At Home in the UK (I sent them a query about the parts I wanted as well as a request for a catalogue) and they can give me the RIS 1.0 to 1.5 Upgrade for £20, which is about $28. Not too bad! Dan (26 years ago, 26-Sep-00, to lugnet.robotics)
 
  Re: NQC & Rotation Sensor
 
(...) Dave, Thanks for the reply, I had a bad feeling it would be this way. If that wasn't bad enough it keeps losing 2 points when stepped from 0 to 16 and back again... Most annoying. I'm going to move to a touch sensor bump mode... This way my (...) (26 years ago, 26-Sep-00, to lugnet.robotics.rcx.nqc)
 
  Re: NQC & Rotation Sensor
 
(...) The reset is a consequence of one of the bytecodes used to configure the sensor. I don't see a way to work around it. (...) This will have the same problem - in fact the generated code is probably identical (except for perhaps order) to just (...) (26 years ago, 26-Sep-00, to lugnet.robotics.rcx.nqc)
 
  Re: AW: V2. Firmware questions
 
Its not private. The sdk 2.0 beta is availible to the public, but they got rid of the easy link. THe other way to get to it is to go to the mindstorms website, click tips and tricks. In the left hand frame, towards the bottom, there is something (...) (26 years ago, 25-Sep-00, to lugnet.robotics)
 
  AW: V2. Firmware questions
 
Tobias, You are right: (URL) 2.2 is a major update to NQC that adds support for RCX 2.0 Firmware and a final Scout API (preliminary Scout support was added in 2.1). Refer to the Release Notes for more detailed information. The RCX 2.0 firmware is (...) (26 years ago, 25-Sep-00, to lugnet.robotics)
 
  AW: V2. Firmware questions
 
Hi Tobias, after downloading firmware V2.0 you can continue to work with the graphical programming tool RIS 1.5 as well as with NQC. But you cannot use the new features ... Up to now you have to switch to the V2.0 programming environment to use the (...) (26 years ago, 25-Sep-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR