To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *23774 (-10)
  Re: Short term memory ablut sensor input???
 
(...) The program doesn't actually record in the Vectors array any information about where it saw an obstacle. It just records which direction the robot went and how far (according to the rotation sensor) during the last leg of the journey. Each (...) (26 years ago, 22-Sep-00, to lugnet.robotics.rcx)
 
  Re: Lego Mindstorms in Swedish television
 
(...) Or for every one, here is the official page from the University: (URL) and drool :) TGIF! /Tobbe (26 years ago, 22-Sep-00, to lugnet.loc.se, lugnet.general, lugnet.robotics, lugnet.technic)
 
  Re: Possible error in assembly guide.
 
Are you getting a good ground???...??? If it works.. then hey! RS232 is +10 to -10 but there is room for slop! +7 to -7 will work too!!!!!!! It just won't drive a cable to the max length of the RS232 spec. Most of the time though people just don't (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
 
  Possible error in assembly guide.
 
Near the end of the "interface/charger serial circuit" heading of the "Assembling The Handy Board" guide, it says measure the voltage of pin 6 of the MAX232, I did that and got -9.5 which is correct. Then I connected pin2 of j9 and pin6 of max232 so (...) (26 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
 
  Re: Remote control
 
I have successfully trained my Sony Integrated Remote Commander RM-AV2000 (retails for $120) with the $20 remote from Lego. I have not tested training the remote from the IR tower, but I'm sure it would work. I'm also sure you could train any (...) (26 years ago, 22-Sep-00, to lugnet.robotics)
 
  RE: Remote control
 
(...) Hey good idea... Now I can justify a fancy learning universal remote to myself! m@ (26 years ago, 22-Sep-00, to lugnet.robotics)
 
  Remote control
 
Has any one tried using a universal remote on the RCX to see if it would work? If it did, $5 is a great improvement over $20! (26 years ago, 21-Sep-00, to lugnet.robotics)
 
  Re: Strong gear assemble?
 
Thanks for the help! After sending out the email, I thought of a way to do it (using a worm and a 40t gear ;), so now it lifts its self. Its interesting to watch as it rises though, because even though its semetricle, it goes up on first one leg, (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
 
  Re: Strong gear assemble?
 
I second the turntable suggestion. Triple black pin two beams to the molded-in mounting lugs and you can make a perfect space to worm-gear the outer ring. As an added bonus you get tons of mounting surface to put the rest of your big- rig (...) (26 years ago, 21-Sep-00, to lugnet.robotics)
 
  Re: Advice on Rotation sensors and steering please.
 
Sorry. No I meant with correcting. My motors were matched pretty well, but without correction there was a large 2-3 foot error. Also the 500->15ft statement was an approximation of the actual numbers, I did this 3 months ago. Andy (26 years ago, 21-Sep-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR