 | | Robot positioning
|
|
Hello all, I am currently building a H board/exp board based robot that has (will have) the following sensors: Diffrential drive wheel encoders, hamamatsu sensors combined with the software from the H board site for motor control and distance counts (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Follow-up to Virus
|
|
It is amazing what can be recovered off a disk, with the right tools. This is the data on the virus files. The document, final1r....doc, within the zip file 478eti.zip is the culprit. "This file was quarantined.f M The file (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | File Contains Virus
|
|
There is a file located on one of the HB sites that contains the Melissa W97 virus. It begins with 478... I am sorry that I can not give you more info as the virus scanning software removed the file, but if you maintain a server with HB files on it, (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: four polariod sonars
|
|
Hi, I read the design a while back... Don't you just control the multiplexor circuit on the handyboard and then call the sonar routines? All sonar use the same routine, aren't they? -- Ray JULIAN REYES <handyboard@media.mit.edu> wrote in message (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: LegOS on LinuxPPC
|
|
(...) Ah, excellent. I saw this post when you posted it, but didn't think about it much at the time. I'll give this a shot and report back. Thanks very much. -- "Do not go gentle into that good night. Rage, rage against the dying of the light." - (...) (26 years ago, 11-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: LegOS on LinuxPPC
|
|
In article (...) I have had better luck with egcs-1.1.2 rather than gcc 2.95.2. I've heard that there's a problem with the way gcc 2.95.2 generates code for memcpy. I've also heard that the fix is to use an assembly version of memcpy instead of (...) (26 years ago, 11-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | LinuxPPC gcc errors
|
|
Ok, I have some error messages here. I'm following the exact instructions in the HOWTO, except for using gcc 2.95.2 instead of egcs 1.1.2. I recall trying egcs with similar results. The make proceeds fine for a while. Then I get this message, and (...) (26 years ago, 11-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Pneumatics and its uses
|
|
(...) What sort of prices are we talking about here? I found some small, low power electronic valves here in Australia; (geez there's a lot of terminology in this industry) they cost $126!! Ouch! I was thinking that you might be able to get (...) (26 years ago, 11-Jul-00, to lugnet.robotics)
|
| |
 | | Re: gluing pneumatic hoses
|
|
How about cutting a short piece from one of those stiff Lego pipes. Pneumatic hoses slip onto these for a tight fit. Then drill a small hole for the pipe (not the hose) into the back of the suction cup, and insert the other end of the pipe into the (...) (26 years ago, 11-Jul-00, to lugnet.robotics)
|
| |
 | | gluing pneumatic hoses
|
|
Does anyone know of a glue that works on the pneumatic hoses? I am trying to attach them to suction cups so that I can make a window washing robot, but nothing I have tried seems to bond. Thank you for any suggestions, Christopher (26 years ago, 11-Jul-00, to lugnet.robotics)
|