To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *22539 (-10)
  Re: LegOS on LinuxPPC
 
In article (...) I have had better luck with egcs-1.1.2 rather than gcc 2.95.2. I've heard that there's a problem with the way gcc 2.95.2 generates code for memcpy. I've also heard that the fix is to use an assembly version of memcpy instead of (...) (26 years ago, 11-Jul-00, to lugnet.robotics.rcx.legos)
 
  LinuxPPC gcc errors
 
Ok, I have some error messages here. I'm following the exact instructions in the HOWTO, except for using gcc 2.95.2 instead of egcs 1.1.2. I recall trying egcs with similar results. The make proceeds fine for a while. Then I get this message, and (...) (26 years ago, 11-Jul-00, to lugnet.robotics.rcx.legos)
 
  Re: Pneumatics and its uses
 
(...) What sort of prices are we talking about here? I found some small, low power electronic valves here in Australia; (geez there's a lot of terminology in this industry) they cost $126!! Ouch! I was thinking that you might be able to get (...) (26 years ago, 11-Jul-00, to lugnet.robotics)
 
  Re: gluing pneumatic hoses
 
How about cutting a short piece from one of those stiff Lego pipes. Pneumatic hoses slip onto these for a tight fit. Then drill a small hole for the pipe (not the hose) into the back of the suction cup, and insert the other end of the pipe into the (...) (26 years ago, 11-Jul-00, to lugnet.robotics)
 
  gluing pneumatic hoses
 
Does anyone know of a glue that works on the pneumatic hoses? I am trying to attach them to suction cups so that I can make a window washing robot, but nothing I have tried seems to bond. Thank you for any suggestions, Christopher (26 years ago, 11-Jul-00, to lugnet.robotics)
 
  Re: Pneumatics and its uses
 
(...) Sounds good! I checked out the Clippard home page and I can't find the valves you are referring to. Nor can I find any relevant EBay auctions. Do you have any more info? One thing that I tried is running the bot off liquified gas. CFC's would (...) (26 years ago, 11-Jul-00, to lugnet.robotics)
 
  Re: Handyboard startup problems
 
Yes, I encounter something similar. Do you use servo on your board? I also have some trouble with the motor ports. I am not sure what causes it. I also have trouble with the motor ports. When I run the motor at 50% power (back or forward), both red (...) (26 years ago, 10-Jul-00, to lugnet.robotics.handyboard)
 
  Re: Expanding the available input/output ports of the RCX
 
in article NEBBIHKHBKAFAGKCCILO...s@olf.com, Ram Meenakshisundaram at rmeenaks@olf.com wrote on 7/7/00 9:58 AM: (...) I am a Lego purist, so I don't want to modify my pieces. Of course, if Lego ever creates an official multiplexer, I'll probably get (...) (26 years ago, 10-Jul-00, to lugnet.robotics, lugnet.robotics.rcx)
 
  H2000 optical position sensor
 
Hi, I am planning to build a position detector with a H2000 chip. The chip is used in several optical mice, for example the H2000/0006 can be found inside the Microsoft IntelliEye mouse. I sill have difficulties in finding the manufacturer and the (...) (26 years ago, 10-Jul-00, to lugnet.robotics.handyboard)
 
  LegOS on LinuxPPC
 
I recall somebody writing to this list about a problem with LegOS under LinuxPPC, and the message seemed to imply that things were mostly happy. I can't make the compiler compile. I'm using gcc 2.95.2. The make proceeds for a good while, then I get (...) (26 years ago, 10-Jul-00, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR