 | | Re: VB Upload Problem
|
|
You can use RcxCC to simply clear the datalog. Duncan ----- Original Message ----- From: Andy Gombos <lego-robotics@crynwr.com> To: <lugnet.robotics@lugnet.com> Sent: Saturday, June 24, 2000 1:04 PM Subject: Re: VB Upload Problem (...) values. (...) (...) (26 years ago, 24-Jun-00, to lugnet.robotics)
|
| |
 | | Re: VB Upload Problem
|
|
(...) I think chris is putting some other info in the datalog. I poked at this briefly when using an early version of Robolab 2.0, but I don't recall the exact details. I think it comes from Robolab trying to use the datalog to record multiple (...) (26 years ago, 24-Jun-00, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Building a Postscript printer?
|
|
Thanks! I grabbed the HPGL info from wotsit.org. Looking around for Postscript->HPGL converters, I found the following: <ul> <li> <a href="(URL)Pstoedit</a>: converts Postscript and PDF into lots of other vector formats (including HPGL). Source (...) (26 years ago, 24-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Building a Postscript printer?
|
|
There is an online version of the manual(at least part of it--the important parts) available at Wotsit www.wotsit.org. Go to printer formats. There is several formats listed, including PCL and HP-GL/2. Andy (...) (26 years ago, 24-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Building a Postscript printer?
|
|
Yup, that was pretty much what I was planning to do. Hack Ghostscript into something to generate a sequence of vector commands to drive the RCX. I was searching for information on a Postscript->HPGL/PCL converter myself since that is basically what (...) (26 years ago, 24-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Making LegOS under Win98
|
|
Hmm. OK, well, if you look in ../Makefile.user (which is included from demo/Makefile) on the very last line you'll see this: %.lx: %.ds1 %.ds2 $(MAKELX) $*.ds1 $*.ds2 $*.lx That is a rule to make all .lx files. So, the rule is there and should be (...) (26 years ago, 24-Jun-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: VB Upload Problem
|
|
ok, so i'm getting a little closer to answering my own question, but i'm still stuck. if i write a new robolab program to take 10 points of light data and then upload it with VB, those 10 points get put into slots 10-20 in the datalog, and points (...) (26 years ago, 24-Jun-00, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Building a Postscript printer?
|
|
(...) You're going to want to use GhostScript for your PostScript interpreter. It already does a good job of interpreting PostScript, so you don't have to write one from the ground up. Then all you have to do is put definitions into the main (...) (26 years ago, 24-Jun-00, to lugnet.robotics)
|
| |
 | | Re: VB Upload Problem
|
|
(...) But I wasn't logging variables... and I never have... I was logging sensor values... and the values were certainly not things like 9, 0, 1, 3, ... (what showed up for values) but were more like 16, 23, 32... (which show up 70 or so values into (...) (26 years ago, 24-Jun-00, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Making LegOS under Win98
|
|
Andy- 3 Questions: 1) What version are you running? 2) Where/when did you get the file from? 3) Can I see the Makefile in question? (should be legOS/demo/Makefile, also legOS/Makefile.user) Neither or these have been changed in more than two months (...) (26 years ago, 24-Jun-00, to lugnet.robotics.rcx.legos)
|