To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *2026 (-10)
  DC Motor and Battery question
 
I am working on a robot using 12V Barber Coleman geared motors. I have followed the instructions on connectingan external battery to the HB. I have about 15V worth of "C" Alkaline batteries connected in series and into the HB. The motors show they (...) (30 years ago, 26-Apr-97, to lugnet.robotics.handyboard)
 
  Question on Kent Farnsworth's IR routine?
 
On the Handyboard software archive, Kent has the following port definitions in the file HB2_EQ.ASM: * equates for Sharp IR sensors -- start at port 4 IR_MASK_ZERO EQU %00000100 IR_ADDR_ZERO EQU $1000 /* port A */ IR_MASK_ONE EQU %00100000 (...) (30 years ago, 26-Apr-97, to lugnet.robotics.handyboard)
 
  Interfacing microprocessors
 
Hi all! I was reading the book mobile robots, by Jones & Flynn, and read about how a port can be used fo tellecommunications between 68hc11aifn's (and others, I assume, in the 68hc11 series). Has anyone tinkered around with this, either with the HB (...) (30 years ago, 25-Apr-97, to lugnet.robotics.handyboard)
 
  Re: hbsonar
 
Check out the multiplexing circuit that I designed. It's on the HB webpage. Can't remember the URL, but you will find a link under my URL (see below) via Mouse 'Data'... I'll be happy to correspond with you on this after I've completed my finals (1 (...) (30 years ago, 25-Apr-97, to lugnet.robotics.handyboard)
 
  mc34064 for ds1233-10?
 
Is it allright if I replace the ds1233-10 with an mc34064? Thank you.. Ferry Toar toar00@rad.net.id (30 years ago, 25-Apr-97, to lugnet.robotics.handyboard)
 
  Re: IC for W95
 
(...) the freeware version of IC runs fine under W95 as a DOS app. Get it from the Handy Board Software Resources page: (URL) (30 years ago, 25-Apr-97, to lugnet.robotics.handyboard)
 
  IC for W95
 
I was wondering if there's a freeware version of IC for windows 95. If so, how can I get it? Also, do I need any registration number? Please respond asap. I'm anxious to program my HB. Thanks, (...) (30 years ago, 25-Apr-97, to lugnet.robotics.handyboard)
 
  Re: To HB or not to HB, that is the question.
 
(...) I emailed the people at Imagecraft and asked them if ICC11 works with the handy board and they said they are working with Fred Martin on it. I noticed on thier home page that they claim to have LCD driver code in a library of version 4 ICC11. (...) (30 years ago, 24-Apr-97, to lugnet.robotics.handyboard)
 
  Re: LCD & serial connection
 
It is possible you have a bum 6811. I have seen 6811's with bad output address lines. this causes mirroring in the RAM as what should be multiple locations get mapped to the same byte in memory. The downloader thinks things are working because each (...) (30 years ago, 24-Apr-97, to lugnet.robotics.handyboard)
 
  LCD & serial connection
 
Thanks to those of you who sent your suggestions regarding the message below. I tried it all (replacing the LCD, checking each pin on both the RAM and the octal transparent latch 74HC373 for continuity, double checking the installed parts, I even (...) (30 years ago, 24-Apr-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR