 | | Hardware Problems
|
|
Hello, I'm having trouble getting my Rev 1.2 Handy Board up and running. It did work once and then the following symptoms: I start the mac based down loader, which download the bootstrap code fine. Both charger board and the handy board's serial (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) He have (had?) some robots here at work that were used in the production areas, and they followed a line on the floor. I've not studied them carefully, but I think they work something like this: Two reflective photosensors are aimed at the (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) This one's pretty easy. Two IR detector/emitter pairs along the bottom, midline of the robot (say, about 1cm or less off the floor). The algorithm is to keep both detectors over the black tape (i.e. a low reflectance reading); if the right one (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Hardware Problems
|
|
(...) All I can add is that is what mine does, and it seemed to break when I hooked up a 'normal' 12V battery charger, which is opposite polarity to the HB charger requirements. According to the diodes in the diagram, this shouldn't be a problem, (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Battery life
|
|
I think I already posted this question some time ago but never got an answer. Is it normal to have the HB run out of battery even when is not being used ?? I know the battery is always working to keep the RAM from erasing, but I'm wondering how long (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
Same question here. I left mine turned off for one night and the next day the battery had almost completely run down! jm (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) I did something like this in an early computer engineering course. The requirements are exactly the same ie. follow a black line. What Chris said is a good start but you should also consider the case when the turn is too sharp; In this case (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
Ive got a pretty crappy answer for you but its the best I can offer; check out how much current the RAM draws from a data sheet and calculate the power it uses (P = IV, where I=RAM current, and V=5v). Divide the mWHr your battery delivers by the (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
rabbit> 3600 since there are that many seconds in an hour. I myself rabbit> have left the handyboard off for periods of 4weeks or more rabbit> and still have had my memory. I just rattled the above off rabbit> the top of my head so, anyone, please (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
The best answer would be to take the mAH of the battery, say X=1500 mAH. Find out the current drawn by the RAM say I=5mA. Divide X by I and you get the number of hours of battery life. This is ofcourse assuming that you have a fully charged battery (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|