 | | power supply
|
|
Anyone? I'm wondering if a 9V Alkaline battery could replace the battery pack in the HB. I'm merely going to use the 9V battery to power the HB and its memory. I'm not going to use any of the 5V-line supplied by the HB. In other words, all the (...) (30 years ago, 3-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | HB Design Question--??
|
|
+---...---+ | NOTICE! I'm posting from a host that is not always available. If your | | email to me bounces or you want to be sure, use 'brat@naxs.com'. THNKS | +---...---+ Fred (or anybody)- I'm doing some last minute sanity-checking on a project (...) (30 years ago, 3-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | photo sensor quesion.
|
|
I understand how a photoresistor that varies in restistance can be connected to the analog inputs. But what about the photelectric elements that generate voltages varying with light. (30 years ago, 3-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: power supply
|
|
I've found that alkaline batteries work well. I used it to power motors too and they seem to work fine. I tested a flashlight bulb and found that it drew 0.79 A at the rated voltage. So alkaline, D-cells at least, can handle the current. ---...--- (...) (30 years ago, 3-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: photo sensor quesion.
|
|
Solar panels? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science and Art ---...--- (...) (30 years ago, 3-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Mini SSC - Scott Edwards
|
|
Hi, I am working in a group to make a six legged robot. We are using the Mini SSC from Scott Edwards to control the servo motors. We've connected the digital output #9 from the Handy Board to the S(in)#2 pin of the SSC. We also connected the signal (...) (30 years ago, 4-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: LCD Panel Substitute
|
|
Any 16x2 LCD with a Hitachi HD44780 controller chip will work. I got mine from wirz electronics at www.wirz.com (go to serial lcd displays and they sell the LCD separate for $8 bucks!) There are lots of displays that use (...) (30 years ago, 4-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: photo sensor quesion.
|
|
If you have a device that uses the handyboard supply to generate voltages then just voltage divide the output to the correct 0-5v and input on the analog ports. If you are using phototransistors or something similar there are lots of photo circuits (...) (30 years ago, 4-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: power supply
|
|
I have never done much battery work and I was wondering if using a separate battery with a common ground to the HB has caused anyone any problems during charging or any other situation. I have common grounded a 3v battery pack to the HB supply to (...) (30 years ago, 4-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mini SSC - Scott Edwards
|
|
(...) Stop the presses! You should have gotten documentation with the SSC but since you are apparently missing it (and its small anyway) the relevant information is that the Mini-SSC uses a serial interface to control its servos. You must send down (...) (30 years ago, 4-Apr-97, to lugnet.robotics.handyboard)
|