 | | Re: IntelliMouse Ripe for Hacking
|
|
(...) I've had one for a fortnight now, no complaints apart form not having one on each computer. (...) They are nothing like the old optical mice which required a special mouse pad. I have even tried it on the cat & it still works fine. I dont (...) (27 years ago, 25-Oct-99, to lugnet.robotics)
|
| |
 | | Re: IntelliMouse Ripe for Hacking
|
|
Hmmm, I like this. Anyone know how much and where I can buy one of these (Best Buy maybe)? Has anyone figured out how close to the surface it has to be to "read" it? I am also wondering if the angle of incidence matters? It would definately be easy (...) (27 years ago, 25-Oct-99, to lugnet.robotics)
|
| |
 | | fried memory
|
|
I suspect that I fried my memory chip. The handyboard downloads Pcode perfectly, but when it tries to synchronize with interactive C, I get an error. While the board is off the 62256-12LP and the 74HC132 chips stay hot. is there a good diagnostic (...) (27 years ago, 26-Oct-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: H8 tools problems on Linux
|
|
(...) Hi! I got the precompiled tools from the LegOS page, tried with both the 'old' and the 'new' set... by the way, the Windows version works fine. Not 0.2.0, but that's not the tools' fault... thanks for all the help Vlad (27 years ago, 26-Oct-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Controlling two robots simultaneously
|
|
(...) In the CyberMaster, open one of them, find the place that controls the radio frequence and rotate it a bit. My knowledge of electronics is ZERO but should exist some kind of knob you can rotate with a screwdriver. Remember that you must also (...) (27 years ago, 25-Oct-99, to lugnet.robotics)
|
| |
 | | Windows 2000
|
|
Anyone already done compatibility tests with the latest Windows 2000 ? I'm specially interested in Spirit.ocx, NQC and RCXCC. Thanks Laurentino Martins [ mailto:lau@mail.telepac.pt ] [ (URL) ] Neither technology nor efficiency can acquire more time (...) (27 years ago, 26-Oct-99, to lugnet.robotics)
|
| |
 | | Re: Windows 2000
|
|
On my W2K Professional RC2 (Build 2128), Spirit.ocx, NQC and RCXCC (the latest versions I found) works perfectly. Ciao Carlo "Laurentino Martins" <lego-robotics@crynwr.com> wrote in message news:4.1.19991026115...test.pt... (...) (27 years ago, 26-Oct-99, to lugnet.robotics)
|
| |
 | | Windows 2000 (fwd)
|
|
(...) I'm working on W2K compatibility, though for my day job. RC 2 has been dropped and RC 3 is not expected out until sometime in late Oct., more likely Mid. Nov. RC 3 is usualy the last release cadidate that goes out before the last beta. At this (...) (27 years ago, 26-Oct-99, to lugnet.robotics)
|
| |
 | | Re: fried memory
|
|
it might not be permanently dead, but if it's not, it's not working. one (or more) of the outputs of these two chips is probably shorted to ground or shorted to +5v. the chips get hot when they try to drive this output to a state other than the one (...) (27 years ago, 26-Oct-99, to lugnet.robotics.handyboard)
|
| |
 | | Eltec 442 Pyroelectric Sensor
|
|
Hi, I purchased an Eltec 442-3 Pyroelectric Sensor from acroname. I know pin 1 is V+ 5V but I don't know how I should connect pin 2,3,4 to my handy bord/expansion board. I want to use the sensor for detecting people and/or candles. How do I connect (...) (27 years ago, 26-Oct-99, to lugnet.robotics.handyboard)
|