To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *14656 (+10)
  Re: couldn't keep myself from it ;-)
 
(...) Whoa. Not so fast. My firmdl3 does the job in 44 seconds, not 53 seconds, so I think firmdl4 is a step backwards. :) Just hold on a bit while I finish packing it up. It is almost done, I promise. The new version (firmdl3) will be MPL. If you (...) (27 years ago, 4-Oct-99, to lugnet.robotics.rcx.legos)
 
  Re: RCX Controlled Air Compressor Tester
 
(...) Here are thoughts on the variability in the tester issues posed. The most important sources of variability in the RCX Controlled Air Compressor Tester and precautions to be taken are as follows: 1. The compressor under test itself may be (...) (27 years ago, 4-Oct-99, to lugnet.robotics, lugnet.build, lugnet.robotics.rcx)
 
  Using 2 polaroid ultra sonic modules simultaneously...
 
How would you use two ranging modules on the the same HB simult.? There are two different ways on the HB web site but they both use TIC3 at Dig. Input 7. How else would I be able to implement this? Any help would be greatly appreciated... -- --Peter (...) (27 years ago, 4-Oct-99, to lugnet.robotics.handyboard)
 
  Re: fast firmware downloader
 
(...) The URL is: (URL) in the nick of time? The original firmdl.c was dated 10/3/98. It is currently 10/3/99 (PDT at least). This was not planned! Like firmdl.c, firmdl3.c is a single file joined from smaller ones for simplicity. I will link a .tgz (...) (27 years ago, 4-Oct-99, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx)
 
  R: R2-D2 Obsession (was Re: What about the Micro Scout?)
 
Tilman Sporkert <lego-robotics@crynwr.com> wrote in message NCBBKPAJLICLDDABDHAM...esw.com... (...) It uses 2 AAA batteries and runs with only 3v. A friend of mine who opened it is absolutely sure the inner motor is the same that you can find (...) (27 years ago, 4-Oct-99, to lugnet.robotics)
 
  Re: equivalent darlington pair
 
Give me your address and I will send you a ZTX614. Colin (...) (27 years ago, 4-Oct-99, to lugnet.robotics.handyboard)
 
  Rcx Command Center version 3.0 available
 
Dear All, I am happy to announce that RCX Command Center version 3.0 is now available. The new version uses NQC 2.0 and is completely compatible with it (e.g. colorcoding, etc.) and contains a translator to translate NQC 1.x code to NQC 2.0. The (...) (27 years ago, 4-Oct-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
 
  Re: RCX Controlled Air Compressor Tester
 
(...) Set up a pump, a valve, and a cylinder like this. pump------Valve---...---cylnder \___...___/ Then put a few drops of oil into each tube AFTER the valve. Turn the valve so the cylinder goes up, and push the pump. Then set the valve to go down. (...) (27 years ago, 4-Oct-99, to lugnet.robotics)
 
  Lubricating Cylinders
 
(...) I've noticed that some of my cylinders are a bit "sticky" or sound like they are grinding. The small cylinders and pumps have a lubricant on them already. On a side note, I'd be careful about what kind of oil I put into these cylinders, since (...) (27 years ago, 4-Oct-99, to lugnet.robotics, lugnet.build)
 
  Re: RCX Controlled Air Compressor Tester
 
(...) Any special type of oil? I've been hesistant about using oil. As I understand it, there is rubber inside the cylinder and oil affects rubber. I'll give it a try! (27 years ago, 4-Oct-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR