 | | Re: empty addresses
|
|
(...) Why do you want to store it at a particular address? Can't you store it into a variable name and let IC take care of where it goes? I think the 16K memory when allocated builds from $0000 and $7FFF towards the middle, so I'd guess any unused (...) (30 years ago, 10-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | IS1U60 IR Demods
|
|
Hello! Can anyone tell me what a fair price would be for this part (IS1U60) would be? I am not trying to make money on anyone I just want to try to share some of these hard to get parts. By the way, sorry I haven't got back to those who responded I (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Signal Diode
|
|
Hey all, Mouser (and Digi-Key, etc.) say that the signal diode 1N4001 has been discountinued, I can't seem to locate any one who has them. This small partis holding up the project. Anybody have extras? Ideas? JTW (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | HB does not enter on bootstrap mode
|
|
Hola, I followed step 4.4 in the HB assembly manual. I hold down STOP-SW while powering on the board, then the battery LED light for 1/3 s, but the power light does not go OFF. I have checked that the MODA signal and the RESET are present at the (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB does not enter on bootstrap mode
|
|
there is no special "mode unlock," so you may have a bad 6811. -fred In your message you said: (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Kent, I've been reading the documentation pertaining to the hookup of the Polaroid 6500 sonar and am a little bit unsure about some of the wording. Can you please verify with me a few things.... When you discuss the connections to the HB, it is (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Sonar Query
|
|
Anyone, I've been reading the documentation pertaining to the hookup of the Polaroid 6500 sonar and am a little bit unsure about some of the wording. Can you please verify with me a few things.... When you discuss the connections to the HB, it is (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Signal Diode
|
|
the 1n4001 is a pwr diode, not a signal, try looking in pwr section. -f In your message you said: (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Signal Diode
|
|
The 1N4001 is the 50v version of a family of diodes (1N4001-1N4007) that cover 50 volts to 1000 volts. In general you could use any of the other versions. I would recommend looking for 1N4002(100v) or 1N4003(200v). As it happens Digikey says they (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | sonar&motor driver
|
|
Hello everyone, If the polaroid sonar sensors are connected as mentioned by kent (ftp site), is it still possible to use motor ports 2 & 3? (30 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
|