To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *14351 (+10)
  Re: before I reinvent the wheel
 
No, but I have used my HP48sx to control the Fascinating Electronics board as well as an NRD535 shortwave receiver. The serial I/O of the HP48 is limited to shield, ground, tx and rx pins so in both cases I had to wire special cables to jumper (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
 
  OVER 1 AMP
 
Now, I recieved two good answers for my problems. 1) Built an H-Bridge 2) Use the LMD18200 Now has any one any documentation on an easy H bridge that I could build without wasting much time? The same goes for the LMD18200, I understand that is not (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
 
  Re: OVER 1 AMP
 
(...) www.yahoo.com, search for "H Bridge", trust me, lots of hits will comeup. Look for the 4QD pages, they talk a lot about H Bridge designs. If you aren't comfortable with electronic design, don't bother though... (...) This IS an H Bridge. Its a (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
 
  Re: OVER 1 AMP
 
Dear Paul, I have an H-bridge that I designed to run big motors. It runs at two amps continuous, and three amps intermittantly. It uses 5 volts for logic from your Handyboard, and 12 volts from a gel cell to run the motors. It also has an analog (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
 
  NQC mentioned in Swedish technical weekly!
 
Hello! When reading this week's 'Ny Teknik' (New Technic), a weekly magazine for engineers, I found a short note about NQC. The article is about Lego Mindstorms, which is just about to be released here in Sweden, and the last part of the article (...) (27 years ago, 23-Sep-99, to lugnet.robotics, lugnet.robotics.rcx.nqc)
 
  Listening to IR via NQC
 
I know that NQC can send IR messages; can it -- or any other command-line program -- listen to the IR port and dump any incoming messages to a file (or stdout)? (27 years ago, 23-Sep-99, to lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
 
  Computer Serial Port Optoisolator
 
This is somewhat off subject, but I am looking for a circuit schematic that will show how to build a serial port optoisolator for my computer. The problem I am having is that once in a while I wire a circuit wrong and end up putting 115V onto the (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
 
  Using 12V supply with Exp Board (2nd posting)
 
Hi all, This is a second posting of the question I posted up several days ago. So I apologize in advance for any inconvenience if you've already got my first posting. Anyways, I am currently using the 9.6V supply voltage on the HB and hoping to step (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
 
  OptoIsolators
 
Regarding the serial port isolator (opto-isolators are good for this) you might see if www.blackbox.com has something along those lines. You could also look up parts similar to the 4N33 to see if you could use something like that in a design. Not (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
 
  Re: MIT Mindfest was(Re: GMLUG.ORG is up!!)
 
(...) Well, I do really want to come to this event, *but* ...I'm afraid I don't have the money to make a trip out to MA in addition to my planned trips places in January and over spring break. I was under the original misconception that MIT was in (...) (27 years ago, 23-Sep-99, to lugnet.org.us, lugnet.robotics.events, lugnet.loc.us.il, lugnet.loc.us.ma)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR