 | | Re: Tasks vs. program slots
|
|
(...) Yes, it appears to use the same packet level formatting. It does use a new bytecode (0xd2) that isn't seen elsewhere. This bytecode needs two bytes of data to follow. These three bytes of "payload" are encoded the usual way with a three byte (...) (27 years ago, 20-Sep-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: OVER 1 AMP
|
|
Do you know where the Caps Lock key is on your keyboard? Look for it, there is a little diode lighting up when it's on. If you see the little light, please do me a favor and before typing your email press the caps lock key once. GET IT? THANKS FOR (...) (27 years ago, 20-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: a couple of new-bot questions from a generally quiet lurker
|
|
(...) I came up with this idea (I don't know if I were the first to do it, though). It worked really great with almost no loss, but there was one problem. The differential and the gearing introduces some backlash, especially if you use those eight (...) (27 years ago, 20-Sep-99, to lugnet.robotics)
|
| |
 | | RE: IRPD revisited
|
|
Hi All What I do for touch sensors/feelers is gear them down .... So the feeler arm has to move further to depress the switch - this allows the robot more movement before destruction of sensors/feeler arms occurs. Also it is easier to put a limit (...) (27 years ago, 20-Sep-99, to lugnet.robotics)
|
| |
 | | Re: a couple of new-bot questions from a generally quiet lurker
|
|
(...) I assume that was me; I posted a message with a link to an LDraw file of a robot I came up with that uses that design. I can't take all the credit for it, however: I was inspired by Simen Svale Skogsrud's web page on his Vector Rover using (...) (27 years ago, 21-Sep-99, to lugnet.robotics)
|
| |
 | | Re: a couple of new-bot questions from a generally quiet lurker
|
|
(...) You can achieve all 5 of these criteria with the standard differtrans, if you put a rotation sensor directly on each motor shaft... [ I've build such a 'bot, and it appears to work pretty well (ie it measures distance accurately, and drives in (...) (27 years ago, 21-Sep-99, to lugnet.robotics)
|
| |
 | | Shaft encoder
|
|
To anybody, I have build a shaft encoder. Where can I get the software driver to evaluate the encoder data? Thanx, Jens (27 years ago, 22-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | OVER 1 AMP
|
|
Thanks everyone for your help, Now, I recieved two good answers for my problems. 1) Built an H-Bridge 2) Use the LMD18200 Now has any one any documentation on an easy H bridge that I could build without wasting much time? The same goes for the (...) (27 years ago, 21-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | OVER 1 AMP
|
|
Oh yeah, one more thing, how about connecting a 5 ohm resistor in series with a DC motor and there are 2 amps flowing, then the resistor is dissipating 20 watts of heat. Now I could have a higher value for the resistor, like 7, 10 ohms, I think that (...) (27 years ago, 21-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: OVER 1 AMP
|
|
You can also stack a few of the original chips to make em work in parrallel. (...) (27 years ago, 21-Sep-99, to lugnet.robotics.handyboard)
|