To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *13621 (+10)
  Droid Dev. Kit, reprise
 
Well, I've built a small "droid" from it now. And I have to admit, since it is a Technic kit, it was fun. It is only a little smarter than a Technic kit that only has a motor because of its programs (such as they are) and the light detector - but, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: Droid Dev. Kit, reprise
 
(...) Well, A week or two back, when I was in Jacksonville, I had a nice conversation with a TRU store manager. He pulled up Mindstorms on his CRT and let me watch. Down at the bottom of the screen was a second something listed as 'RIS' (or (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  r/c servos
 
In response to the question about RC servos, I noted, while probing the signals on the I/O ports with a scope, that the motor power settings result in varying duty cycle square waves from 1:7 through 7:1 and finally full on as the parameter value (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: [Off-Topic] Re: X10 X-Cam
 
<SNIP> (...) Actually I believe the software that comes with the "MP3 Anywhere" is something similar to Ampapod (URL) allows you to use the X10 Mouse Remote to control Winamp. Ampapod is strictly 9x/NT though. (...) X10 is the king of marketing (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
I love the idea of controlling an R/C servo with the RCX, but I don't think it is possible with only software. On the other hand, a relatively simple circuit could be made to convert a duty cycle to a R/C servo signal. Is anyone out there interested (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
If the pwm is really being controlled by an 8 bit counter, that might be fine for the servos. The current rcx output has a cycle time of 8mS and uses 1mS increments. If those are the top 3 bits, then the resolution is 5 bits worth or 0.03mS. This (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) It is a software-based PWM. The topic of controlling a servo with the RCX has been discussed before. Generating the pulse stream for a servo would not be too difficult with the RCX, assuming you program the H8 directly using e.g. LegOS or (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) To get rid of the speculation here, the PWM is controlled by a programmable timer that the code in ROM configures to generate an interrupt every 1 ms. Output for each of 8 power levels is stored in a small table of waveforms, with the 1 ms (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: Droid Dev. Kit, reprise
 
Or could it be that new 2 in 2 out screen programmable (blue RCX) RIS? JT -----Original Message----- From: Ray Sanders [mailto:rsanders@gate.net] Sent: Friday, August 20, 1999 6:03 AM To: lego-robotics@crynwr.com Subject: Re: Droid Dev. Kit, reprise (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: X10 X-Cam
 
Don't buy the X-10 system expecting to use it for robotics. Those 2.4Ghz transmitters are directional and therefore are not well suited for the robotics application. Go to Best Buy or shopping.com etc. and buy a 900Mhz transmitter/receiver (actually (...) (27 years ago, 20-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR