 | | Re: pneumatics & mindstorms?
|
|
(...) Yes, I guess friction is the answer. 1) The difference in the surface of the pistons between the two kind of pumps is important. I didn't compute the ratio, but imagine can easily be 1:10 or even more. To get that ratio you need to gear down (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) How much did they cost? It's a real pain to get them by any other means... Stuart -- Did you check the web site first?: (URL) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) It has to be reversible from the RCX brick's point of view, since there is no hardware on the RCX to forcibly reprogram its ROM. Perhaps on the PC side it is not reversible, but there is always the uninstall new, reinstall old process, which I (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) [snip] (...) I truly doubt that LEGO in going to create a new OCX. Their strategy was always focused in creating the maximum sowtware with the less work possible. The OCX compatibility between two very different devices like the RCX and (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Reading Serial Port
|
|
It isn't hanging, it's a blocking read until it recieves some specified number of characters. You can use a non blocking read by specifying O_NONBLOCK, in which case read() will return immediately. The Linux serial programming HOWTO is very good, I (...) (27 years ago, 29-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) sequence (...) only (...) 51.99 FF, that means 7.93 Euros. About 8.40 USD at current exchange rate. The problems is they don't ship abroad. To get them here in Italy I had to send a check in FF and ask them for shipping to a French address (my (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: R: Reading Serial Port
|
|
also remember that at 9600 baud or higher, you may not see the flashing of the serial LEDs. try setting the baud rate to 300 or even 110 if you're doing visual-flash debugging. fred In your message you said: (...) (27 years ago, 29-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | A RCX 'Beacon'
|
|
Well, I'm not an expert when it comes to small electronics and making them, so I thought I would post this question to this list. After working with the RCX for nearly a year now, I've found a tool/sensor that I would really like to have, but no (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: New pbFORTH 106 release
|
|
Hi Ralph, Thanks for the new release. I have a couple of questions: 1. How do I use BUTTON_GET? The documentation says it just expects to find an address on the stack, but I get this: RCX_BUTTON BUTTON_GET BUTTON_GET ? stack underflow 2. What (...) (27 years ago, 29-Jul-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: A RCX 'Beacon'
|
|
(...) Brian, I share your dream. It's a great idea. Surprisingly enough just this morning I wrote an email to Al Thiele asking for the same thing. I'm obsessed by the problem of knowing the robot position. I had some success experimenting odometry, (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|