 | | Re: Voice Recognition Hardware
|
|
Try to track down a company called "CoVox". These guys used to have a speech recognition device that ran on the Apple II (6502) that was pretty cool (speaker dependent of course). Also there is a speech recognition chip for use in toys the HM002 or (...) (27 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Best (disposable) battery for the RCX?
|
|
I've been using Duracell alkalines and they don't seem to last very long at all. Has anyone found a brand that works better? (I've avoided the Duracell "Extra" (or whatever their premium supermarket battery is) because the package seems to imply (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Best (disposable) battery for the RCX?
|
|
I use Ray-o-Vac Renewals (rechargeable alkalines), and am quite pleased with them. For best performance they should be recharged very often - even if only partially drained. I just get in the habit of swapping out a set of batteries before starting (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | The IR FIX -- was: Re: Is IR considered broken?
|
|
(...) I had the same problem. (...) Here's the fix: enclode the old handler code in #ifdef TRASH, use the new #else part. I'll say a few things about the motivation below. (If you prefer to patch, download (URL) it's based on LegOS 0.1.7 but should (...) (27 years ago, 26-Jul-99, to lugnet.robotics.rcx.legos)
|
| |
 | | better test value for touch sensors
|
|
FYI: The simple-rover example uses an unsafe test value for touch sensors. Touch sensor should be tested against <0xf000, NOT <0x2000 (e.g. simple-rover.c) Reason: Not pressed has a constant value >0xf000. Pressed varies depending on battery change, (...) (27 years ago, 26-Jul-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Lego Scanner - DTM
|
|
Hi all. I have pics and info of my latest creation - A Lego Scanner (~25 dpi) I like to call DTM (Digital Terrain Modeller). To see it go to www.astolfo.com/lego and go to the Mindstorms section. CIAO (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Zapped Firmware
|
|
-Apparently I have twice erased my firmware by putting a heavy load on motors attached to the RCX. The batteries do not appear to be dead. Is this normal behavior? -JW Jonathan Woodward woodward@guesswork.com (URL) find your (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Weak Motor
|
|
(...) It wouldnt be wise to directly connect your 12V supply to the Handy Board... even if it doesnt cause damage to your Handy Board, I dont think your motor will be able to draw sufficient current from the motor port to run properly. Rather, you (...) (27 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Temperature Sensor
|
|
Does anyone know the exact characteristics of Lego's temperature sensor? It's easy enough to buy a thermistor and hook it up, but I'd like the temperature readings to be accurate. I've seen thermistors described by a resistance at 25 degrees C and a (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Interfacing handyboard with Basic Stamp2
|
|
Hello to everybody. I would like to ask if is possible to interface the handyboard with the basic stamp2 using not the RS232. Thanks beforehand. (27 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
|