 | | Re: Quickcams
|
|
(URL) check these guys out they have done what your thinking... good luck phil (...) (27 years ago, 28-Jun-99, to lugnet.robotics.handyboard)
|
| |
 | | FW: Alternate C compiler for LegOS
|
|
Luis, here's a forwarded message with the links to Gavin's executables. You need to download the latest Cygwin distribution too, from (URL) (...) Alternatively, have a look at (URL) I've done a similar but lazier job of just providing an add-on lump (...) (27 years ago, 28-Jun-99, to lugnet.robotics.rcx)
|
| |
 | | Re: Moving Straight
|
|
I use the 9 gram Piezo gyro in my Hand Launch Glider to keep it moving level despite strong wind conditions. Could you use that in your robot as a "Rudder" input? The 9 gram Piezo gyro costs about 9,500 yen here in Japan. That is about $80.00. I (...) (27 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: The Lego Robogladiator Event that happened at E3
|
|
(...) (URL) the rules section there is a line about wireless control which says, I quote. "The RCX brick can send and receive 255 discrete commands over the IR port." Is there some more info on this interesting snippet out there please? James from (...) (27 years ago, 29-Jun-99, to lugnet.robotics.events)
|
| |
 | | RE: Moving Straight
|
|
Many people use trial and error to come up with a wheel differencial factor that should always be applied so that even without looking at the encoders the robot should move pretty straight. If you do the compensation on the fly that is OK but during (...) (27 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: Moving Straight
|
|
Our first challenge was to get our robot to move ahead straight. There seemed to be a difference in the motor torques. We used shaft encoders and compared the counts every 200 to 500 milliseconds. Slowing down the motor that had a higher count, for (...) (27 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
|
| |
 | | Windows file mirroring
|
|
OK, I've now mirrored the two (apparently) necessary files for LegOS under windows at this URL: (URL) those of you in the US, this should provide a faster download of Gavin's stuff (though not necessarily by much, since Gavin's site is surprisingly (...) (27 years ago, 29-Jun-99, to lugnet.robotics.rcx)
|
| |
 | | Re: The Lego Robogladiator Event that happened at E3
|
|
(...) In the RIS code the "Send to RCX" and "RCX Sensor Watcher" allow you to send and recieve between two RCX units. This is how we were able to get wireless control. Each "Send To RCX" and "RCX Sensor Watcher" requires a # between 1 and 255. The (...) (27 years ago, 29-Jun-99, to lugnet.robotics.events)
|
| |
 | | legOS for Win 95/98 was: legOS make newbe question
|
|
I must have been sidetracked and posted this by mistake to ..build. Sorry, -Phil (...) (27 years ago, 29-Jun-99, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: LM35 Temp Sensor
|
|
The output pin of the LM35 gives you the ambient temperature in 10mV/degree C directly. The 47k pullup resistor will form a voltage divider with the output. You either have to do some conversion (complicated) or eliminate the pullup (easy).... Paul (...) (27 years ago, 29-Jun-99, to lugnet.robotics.handyboard)
|