 | | HB - fast sensor reading
|
|
Hello, I have a clock signal of 5 kHz and an analog signal. (There are in total 128 clock pulses) I need to read in the analog signal every time the clock signal is high. So I need to read the clock signal with at least 10 kHz. I tried this with IC, (...) (30 years ago, 7-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: I think I fried my board!!
|
|
Yes it is probably the inductor. It acts as a fuse in many situations. You are lucky -- it could have been much worse. -Fred In your message you said: (...) (30 years ago, 7-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: I think I fried my board!!
|
|
keith-- you might have fried the motor ground to logic ground connection. a couple of times in my lab using 6.270 boards people shorted motor high to logic ground, with the result being a vaporized trace between the two grounds (the inductor was not (...) (30 years ago, 7-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | (# of sensors)
|
|
Can anyone tell me if it's possible to run more than one servo off the Handy Board? My design group and I are building a robot that will perform an autonomous search routine. We're in the rough developement stage and really trying to pin down just (...) (30 years ago, 7-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | HB learning time
|
|
Hello, I am a beginner in Robotics and have looked at the Handy Board, Miniboard, BotBoard, and Basic stamps. I have decided I think I like the HB. The only thing is I want to make a mobile robot or arm that has basic AI, maybe using Subsumption. I (...) (30 years ago, 8-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | (Reply to Mr. Ericson)
|
|
Mar, I responded last night to your personal address and to be quite honest, I'm not sure if I sent it to the right address..so let me say again, in response to your question about what kind of IR sensors my design group and I plan on using--we (...) (30 years ago, 8-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | Interfacing HB to PIC
|
|
Has anyone interfaced the HB to a PIC chip or other microcontroller without using the primary serial lines? I am wondering if maybe there was an I2C or SPI implementation done somewhere using digital outs. (30 years ago, 9-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Interfacing HB to PIC
|
|
(...) Are you referring to using the SPI port on the Handyboard, or simulating the SPI function via other ports? If you run the handyboard as a master, then the handyboard is responsible for providing the clock output used to capture the data by the (...) (30 years ago, 9-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: Interfacing HB to PIC
|
|
I really didn't have anything in mind other than the solution. How could you use the SPI port to communicate with the PIC? (...) (30 years ago, 9-Jan-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: Interfacing HB to PIC
|
|
(...) Well, in that case, the SPI port is what you want, provided an SPI port is also available on the PIC. Then just set up the SPI config, load the register and the computers exchange 16 bits shifted on a clock generated automatically by the (...) (30 years ago, 9-Jan-97, to lugnet.robotics.handyboard)
|