 | | Re: Lego Network Protocol questions
|
|
(...) So of course I was curious about getting rid of the complements. Apparently, they are not necessary, or so my testing so far seems to indicate. Under the several lighting conditions I tried, and for distances of up to 27' (the farthest I could (...) (27 years ago, 6-Jun-99, to lugnet.robotics.rcx.legos, lugnet.robotics)
|
| |
 | | tm-and-ir (again)
|
|
Hi all, I've been using Legos without any major problems but never got the tm-and-ir demo to work properly. I can receive characters on the RCX fine but when the 'view' button is pressed (within 3 seconds) the results are normally junk on the screen (...) (27 years ago, 7-Jun-99, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: Lego Network Protocol questions
|
|
(...) I'll back you up on this. My pbFORTH sends a simple character stream and it seems to work fine. No complements are necessary. I sure would like to be able to keep the RCX tower alive, though. I wonder if it's the character going through that (...) (27 years ago, 7-Jun-99, to lugnet.robotics.rcx.legos, lugnet.robotics)
|
| |
 | | Re: New rubber tracks help
|
|
(...) Call the LEGO consumer affairs number 1-800-453-4677 and complain about them. They will send you a new set. I have done this twice with sets that have "bad" rubber tracks. There seems to be a quality control issue with these parts... DLC (27 years ago, 7-Jun-99, to lugnet.robotics)
|
| |
 | | LEGO parts
|
|
Hello! Anybody knows who sells LEGO parts in USA and ships them to foreign countries. Thank you Aldo Gentile aldo@lacapital.com.ar Aldo Gentile Diario LA CAPITAL Rosario, Argentina (27 years ago, 7-Jun-99, to lugnet.robotics.handyboard)
|
| |
 | | RCX Tower Internals
|
|
Hi All. I've just had some wierdness with my tower and decided to open it up to see what's inside. My basic issue is that the two emitters and the detector are not lined up (even close) with the "Clear" lens section on the front of the tower. Is (...) (27 years ago, 7-Jun-99, to lugnet.robotics.rcx)
|
| |
 | | GP2D02 IR sensor
|
|
Where can I find specific instructions on how to hook up the GP2D02 to the Handy Board? Thanks! Salpi Aroyan Tapehead Manufacturing Engineering International Business Machine Corporation saroyan@us.ibm.com (408) 256-8251 (27 years ago, 7-Jun-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: LEGO parts
|
|
A good source for Lego and Lego Dacta parts is: Pitsco Lego-Dacta P.O. Box 1707 Pittsburg, Kansas (USA) 66762 1 (800) 362-4308 1 (888) 534-6784 (FAX) I called them for a free catalog and found them to be very helpful. Regards, Rob Lear -----Original (...) (27 years ago, 8-Jun-99, to lugnet.robotics.handyboard)
|
| |
 | | micro motor sometimes stuck
|
|
Why does the micro motor sometimes get stuck, and then I have to turn it by hand to restart it? Hao-yang Wang (27 years ago, 8-Jun-99, to lugnet.robotics)
|
| |
 | | Re: RCX Tower Internals
|
|
(...) Mine is like this too, I think. See (URL) compare to see if they look similarly. For me at least, the emitters and detector are slightly above the "clear" section. (...) For me at least, there is no way the components can line up with the (...) (27 years ago, 8-Jun-99, to lugnet.robotics.rcx)
|