 | | withdraw
|
|
Dear Sir, Please take from the list. Thanks for all, Jorge (27 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: withdraw?
|
|
I'm not sure how "signatures" work, but maybe one could be added to every handyboard message reminding people of the proper procedure on how to take themselves off the mailing list? Just a suggestion! Dave (27 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
 | | L.A. Store
|
|
Hi Does anybody know about a electronic or robotic store at L.A. (Los Angeles).? And the Address. Please Thanks Daniel ---...--- " `BETTER´ IS THE ENEMY OF `GOOD ENOUGH´" ---...--- (27 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Using SPI
|
|
I am using the SPI port to communicate with another Handy Board. I have written a routine in IC that will pass bytes between controllers just as it is supposed to work. However, the code is not very clean and it is very touchy. Change one thing and (...) (27 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: New creations: VCR and Car
|
|
(...) It's an Olympus D220L, pretty basic but it does the job. Sometimes I wish it was a little less wide-angle, but otherwise good. (...) Yes it does, but not so you'd notice. I messed around with it to get the steering link at the right height to (...) (27 years ago, 22-May-99, to lugnet.robotics)
|
| |
 | | Re: New creations: VCR and Car
|
|
Fredrik Glöckner wrote in message ... (...) And I use Larry the same way. Moz (27 years ago, 22-May-99, to lugnet.robotics)
|
| |
 | | Re: New creations: VCR and Car
|
|
(...) And we're all happy. ;-) Fredrik (27 years ago, 23-May-99, to lugnet.robotics)
|
| |
 | | More about problems with RCX and ROBOLAB for Macintosh
|
|
---...--- More about problems with RCX and ROBOLAB for Macintosh ---...--- I can't get any communication from Macintosh to RCX with the ROBOLAB software. The RCX and the ir tower are okay - the ROBOLAB connection from a Windows98 pc to RCX shows no (...) (27 years ago, 23-May-99, to lugnet.robotics)
|
| |
 | | Midi?
|
|
Hi Folks, I was wondering if anyone had any code to input/output Midi from the Handyboard? Thanks, Chris Prosser (27 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Midi?
|
|
(...) Chris, check: (URL) is a midi library for the Hb here. Best, Duncan (27 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Sony Robotic Dog: Check it Out!
|
|
(URL) dog is wild! It can learn behaviors and it can be reprogrammed! Ross M. Tonkens, M.D. Medical Director Primary Care of Nevada 100 North Green Valley Parkway Suite 240 Henderson, NV 89014 702 914-7120 VOICE 702 914-7129 FAX (27 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Sony Robotic Dog URL correction
|
|
I misquoted the URL. Typed so fast, I left out the world wide web prefix. It should read: (URL) Tonkens (27 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Using SPI
|
|
(...) Gary, We used the PA7(transmitting board) and PD0(receiving board) in wireless and wired mode. This is quite easy to do. Pete Eacmen have done the wired stuff while I did the wireless stuff. With wired one, you can transmit @9600 baud with no (...) (27 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Not lego, but interesting...
|
|
Good job for Sony engineers (URL) José Antonio Vacas Martínez (...) -- Did you check the web site first?: (URL) (27 years ago, 19-May-99, to lugnet.robotics)
|
| |
 | | Windows CE
|
|
does anyone know of a way to program the RCX from a CE device? -- Did you check the web site first?: (URL) (27 years ago, 20-May-99, to lugnet.robotics)
|
| |
 | | Problems with Macintosh and Robolab
|
|
---...--- Problems with RCX and ROBOLAB for Macintosh ---...--- I can't get any communication from Macintosh to RCX. The RCX and the IR-tower are okay - the connection from a Windows98-PC to RCX shows no errors. Trying any port (modem or printer) I (...) (27 years ago, 21-May-99, to lugnet.robotics)
|
| |
 | | Sony Robotic Dog: Check it Out!
|
|
(URL) it out. The robot learns from experience. It can also be programmed to exhibit new behaviors. Ross M. Tonkens, M.D. Medical Director Primary Care of Nevada 100 North Green Valley Parkway Suite 240 Henderson, NV 89014 702 914-7120 VOICE 702 (...) (27 years ago, 23-May-99, to lugnet.robotics)
|
| |
 | | Re: Windows CE
|
|
I think the best way would be to port NQC, Dave Baum makes the source freely available. (...) -- Did you check the web site first?: (URL) (27 years ago, 24-May-99, to lugnet.robotics)
|
| |
 | | Re: Problems with Macintosh and Robolab
|
|
I don't think speed is a problem. I was running an early version of Robolab on a 604e/132MHz. It was annoyingly slow to use, but it was able to talk with the RCX. You may want to try the IR tower in both "near" and "far" modes (that's the switch on (...) (27 years ago, 24-May-99, to lugnet.robotics)
|
| |
 | | Fwd: Re: Problems with Macintosh and Robolab
|
|
Hallo Dan, yes, I have already updated the serial drivers - without any result. NQC connects fine but not ROBOLAB. I wanted to try iconic programming with ROBOLAB. Ralf (...) to (...) robolab (...) try (...) --- Sent through Global Message Exchange (...) (27 years ago, 24-May-99, to lugnet.robotics)
|