 | | IR test reports "Rubbish" when I run test.c
|
|
When I try to get the values for my IR transmitter the test.c reports that it is a bad. It calls it 'rubbish' why would that be? -Peter (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: handyboard clock speed
|
|
(...) From the data books for the 68HC11, if you have any version of the E-series (except for perhaps one, a low-power version?), you can run them at up to a 3MHz E-clock (12MHz crystal). I haven't looked at the rest of the handyboard schematic with (...) (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: legOS Network Protocol
|
|
(...) given (...) lego (...) [ stuff about lego/native collisions ] (...) of a (...) on (...) I was wondering, since people are considering using tags in the LNP frame to signify local to local messages, could we not also use this to "label" non (...) (28 years ago, 23-Apr-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: handyboard clock speed
|
|
(...) yes, this is right. the fastest you can go with the 52-pin 6811s is 12 MHz crystal --> 3 MHz system clock (i'm pretty sure). so this is only 1.5x over the stock HB. so you've got the issue Curt pointed out with not only the downloader, but (...) (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: handyboard clock speed
|
|
(...) Not going to mention the free Otto/Steven/Keith/Curt GCC-2.8.1 HC11 port? I'm hurt. ;-) Maybe you need to add my web & ftp pages to your free software page, now that I have a GCC Handyboard library available? GCC/HC11 patches are available (...) (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Pics of 1999 Mindstorms items
|
|
The press room at www.legomindstorms.com has some new pictures of the two new kits due out this year. From these pictures, it's clear that the "Scout" unit - in the Robotics Discovery Kit - is very similar to the RCX; it has only 2 inputs, and (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
|
| |
 | | Reading sensors at equal intervals.
|
|
Is it possible (with the standard firmware) to read the RCX sensors (actually, ideally, to run any old subroutine) at equal intervals, ie like every 100ms or something? (I assume it must be, otherwise you couldn't measure speed with the angle (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
|
| |
 | | Steer kit
|
|
I bought the Steering kit, 5295, and now can't envision how all of the pieces can be used. Does anyone have any examples they could share? -- Did you check the web site first?: (URL) (28 years ago, 24-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Steer kit
|
|
David Cuthill <lego-robotics@crynwr.com> wrote in message news:01BE8DCB.0A59FE...ome.com... (...) One of the models on this page shows some of those parts. Sorry that they are not closeup. (URL) (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
|
| |
 | | Re: IR test reports "Rubbish" when I run test.c
|
|
Test.c expects to see both short and long pulses of IR, and it tries to accept timings from any remote. It times the signals it receives and records the lengths of the shortest and longest pulse. It then uses the midpoint of these values as a (...) (28 years ago, 24-Apr-99, to lugnet.robotics.handyboard)
|