 | | Re: What good is the small gear motor?
|
|
Rob, I have had similar problems with the red micromotor. The motor will jam like this if the load is large enough to stall it. I was attempting to make a 'distributed' motor using three micromotors connected to the same power plate. This (...) (28 years ago, 14-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Smooth PWM for IC3.2?
|
|
Eric/MSMKatz Newton Labs does offer smooth PWM routines for IC3.2. Check ftp://newtonlabs.com...mooth-pwm/ for details. I have used these with my handy board and expansion board (only simple test) and it worked fine. It does require some changes to (...) (28 years ago, 15-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: UK Mindstorms competition
|
|
(...) More information (especially when they've decided the rules etc!) will be posted here (although there's not much there yet): (URL) you check the web site first?: (URL) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | Re: What good is the small gear motor?
|
|
In article <37154737.D4E6169F@home.com>, robkc <robkc@home.com> writes (...) Use a crank shaft and con rod like a piston engine. (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | AW: Lego Bots in Germany??? (A)
|
|
(...) annoy (...) Sure, but I a m not a 9-12 year old kid. They could at least sell it below the counter or print a warning on the box and let me decide whether I might take the risk or not. Anyway: Thanks, obrigado, grazie, dank je and tak for your (...) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | Re: UK Mindstorms competition
|
|
In article <Pine.LNX.3.96.99041...418.1891E- 100000@moulton.eng.cam.ac.uk>, S. Crawshaw <sc10003@eng.cam.ac.uk> writes (...) I have had an email from reading.ac.uk to say that the actual URL for the competition itself is (URL) Regards - Peter (...) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | Novice group
|
|
There seems to be a lot of discussion about creating new groups lately. I would like to see a new robotics group. Don't get me wrong, there's nothing wrong with lugnet.robotics, but the level of most of the discussion in there is way over my head. I (...) (28 years ago, 15-Apr-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: Novice group
|
|
(...) Have you tried it on a hard floor with fresh batteries. Mine did not work so well on carpet. Your code should be full speed in one direction then reverse both motors to go full speed in the other direction. I Dave David Warnock Sundayta Ltd -- (...) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | Tornado and more
|
|
Please come and visit my Web Site at: (URL) you can find a Tornado, a Professor (conversation between two RCX) and a Dunkobot challenge. Marcus Fischer Mellbin -- E-mail: marcus@fischer-mellbin.com (URL) (28 years ago, 15-Apr-99, to lugnet.robotics)
|
| |
 | | Beyond the jitters...
|
|
Well my code does make constant calls to printf() and motor() (although with the original PWM code). I did notice the jitters more on the low end. now I've put aside the head rotation and sonar routines and will start on the encoders. I am (...) (28 years ago, 15-Apr-99, to lugnet.robotics.handyboard)
|