To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10736 (+10)
  Re: Servo DEinitialization.
 
I'd go for the Coke can idea. Sounds like a surer shot. I thought init_expbd_servos(x), where x = integer from 0 to 5, was used to initialize the servos individually. Stupid me. I've been using init_expbd_servos(5), and, since I only had #5 hooked (...) (28 years ago, 13-Apr-99, to lugnet.robotics.handyboard)
 
  Re: clutch gear
 
(...) No, but it's probably the cheapest, unless it's in a Dacta spare parts kit I don't know about. Target had the 3735s on sale for over 50% off. It's also in the 8479 Bar Code Multi set, but that's $160. These are the only two sets that have it (...) (28 years ago, 13-Apr-99, to lugnet.robotics)
 
  Dark seeker project
 
I have finally built a creation with my Mindstorms kit that uses all of the sensors (some twice) and all of the motor connections! It has two bump switches for a collision detector on the front, one of my RCX IRPD modules to try to detect potential (...) (28 years ago, 13-Apr-99, to lugnet.robotics)
 
  Re: Servo DEinitialization.
 
(...) as it says in the docs: init_expbd_servos(int action) If action is zero, servo control signals are disabled. If action is non-zero, servo control signals are enabled. Control signals are disabled by default every time the Handy Board is reset. (...) (28 years ago, 13-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Servo DEinitialization.
 
Sorry. I'll reread the documentation. I was going by memory. Fred G. Martin Fred G. Martin (...) Ross Tonkens (28 years ago, 13-Apr-99, to lugnet.robotics.handyboard)
 
  Re: **lego motors?**
 
(...) I don't think that it would take up a lot of space at all. In fact, the largest part should be the motor that is used to engage/disengage the gear. Using a tractor hub, two 16-T gears, and two axles (with other parts to hold this all together, (...) (28 years ago, 13-Apr-99, to lugnet.robotics)
 
  Re: **lego motors?**
 
Laurentino Martins wrote in message <4.1.19990412164203....90.220>... (...) gears, with a rubber band pushing it to one of the sides...? There has been a couple of versions of just what you describe, however I don't have the URLs. Sorry... about (...) (28 years ago, 13-Apr-99, to lugnet.robotics)
 
  just to say hi
 
hi (28 years ago, 13-Apr-99, to lugnet.robotics)
 
  Has anyone an icb-routine for 9600b serial connection ?
 
Hi, i used the serialio.c routines to establish a data connection between the Handyboard and a Linux PC and encountered the same problems already mentioned in the mailing list: 1) Only char by char transmission with sleeps between transmissions (...) (28 years ago, 13-Apr-99, to lugnet.robotics.handyboard)
 
  Re: SENSOR_READ doesn't return 0
 
(...) I am just dabbling at the moment, trying a few words to try and get them debugged. In order to fully port the SpeedBot (currently in NQC) I'll need multitasking... (...) Oh, good - I wondered if I'd got versions mixed up somewhere. It would be (...) (28 years ago, 13-Apr-99, to lugnet.robotics.rcx.pbforth)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR